Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK
RM1440E _58 Vehicle Interior _056155 DOOR LOCK _0274059 FRONT DOOR LOCK G

DOOR LOCK  FRONT DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69320 1.INSPECT FRONT DOOR LOCK ASSEMBLY LH

a.

Check the door lock motor operation.

i.

Apply battery voltage to the motor connector and check the operation of the door lock.

B184438E10
1.99,2.321 2.365,2.484 0.375,0.163 10 *a 2.529,2.02 3.039,2.194 0.510,0.174 10 *b 4.251,0.724 4.696,0.947 0.445,0.223 10 *c 4.458,1.948 4.662,2.132 0.205,0.184 10 L 6.218,1.948 6.517,2.128 0.298,0.180 10 UL 5.72,1.802 6.166,2.011 false 5.031,1.802 4.584,2.011 false 5.639,2.388 5.893,2.545 0.254,0.158 10 E 5.007,2.388 5.486,2.565 0.479,0.177 10 LSSR 5.267,2.027 5.204,2.368 false 5.484,2.004 5.665,2.362 false

Text in Illustration
*a Lock *b Unlock
*c Component without harness connected
(Front Door Lock Assembly LH)
- -

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)
Unlock


If the result is not as specified, replace the front door lock assembly.




b.

Check the detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (LSSR) - 7 (E) Lock 10 kΩ or higher
8 (LSSR) - 7 (E) Unlock Below 1 Ω


If the result is not as specified, replace the front door lock assembly.




c.

Check the door lock and unlock switch.

i.

Measure the resistance according to the value(s) in the table below.

B184437E14
2.468,0.844 2.888,1.014 0.420,0.170 10 *a 2.227,1.951 2.735,2.132 0.507,0.180 10 *c 2.738,1.567 3.048,1.722 0.310,0.155 10 *b 4.253,0.906 4.560,1.210 0.307,0.304 10 *d 5.315,2.347 5.446,2.528 0.131,0.180 10 E 4.482,2.251 4.723,2.404 0.240,0.153 10 UL 5.043,2.347 5.208,2.490 0.164,0.142 10 L 5.365,2.044 5.365,2.34 false 5.077,2.044 5.077,2.34 false 4.923,2.022 4.651,2.294 false

Text in Illustration
*a Lock *b Off
*c Unlock *d Component without harness connected
(Front Door Lock Assembly LH)

Standard Resistance:
Tester Connection Switch Condition Specified Condition
9 (L) - 7 (E) Lock Below 1 Ω
9 (L) - 7 (E)
10 (UL) - 7 (E)
Off 10 kΩ or higher
10 (UL) - 7 (E) Unlock Below 1 Ω


If the result is not as specified, replace the front door lock assembly.




Hide 69310 2.INSPECT FRONT DOOR LOCK ASSEMBLY RH

a.

Check the door lock motor operation.

i.

Apply battery voltage to the door lock motor connector and check the operation of the door lock.

B184439E29
5.188,1.99 5.031,2.271 false 5.385,1.99 5.635,2.271 false 4.885,1.781 4.365,1.875 false 5.677,1.76 6.063,1.865 false 1.26,1.979 1.458,2.167 0.198,0.188 10 false *a 1.865,2.208 2.135,2.396 0.271,0.188 10 false *b 4.396,0.896 4.635,1.115 0.24,0.219 10 false *c 5.438,2.302 5.875,2.5 0.438,0.198 10 false LSSR 4.979,2.302 5.125,2.5 0.146,0.198 10 false E 4.198,1.844 4.333,2.052 0.135,0.208 10 false L 6.135,1.823 6.406,2.021 0.271,0.198 10 false UL

Text in Illustration
*a Unlock *b Lock
*c Component without harness connected
(Front Door Lock Assembly RH)
- -

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)
Unlock


If the result is not as specified, replace the front door lock assembly.




b.

Check the detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
7 (LSSR) - 8 (E) Lock 10 kΩ or higher
7 (LSSR) - 8 (E) Unlock Below 1 Ω


If the result is not as specified, replace the front door lock assembly.