Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK
RM1440E _58 Vehicle Interior _056155 DOOR LOCK _0274060 REAR DOOR LOCK G

DOOR LOCK  REAR DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69060A 1.INSPECT REAR DOOR LOCK ASSEMBLY LH

a.

Check the door lock motor operation.

i.
B164415E08
0.208,0.222 0.484,0.447 0.276,0.225 10 *a 2.305,3.908 2.778,4.064 0.473,0.156 10 *c 1.792,3.905 1.999,4.057 0.207,0.151 10 *b 0.166,3.678 0.263,3.820 0.097,0.142 10 L 0.451,4.374 0.566,4.516 0.114,0.142 10 E 1.1,4.374 1.494,4.516 0.394,0.142 10 LSSR 1.395,3.678 1.594,3.820 0.199,0.142 10 UL 0.54,3.87 0.265,3.758 false 1.158,3.874 1.395,3.76 false 0.647,4.063 0.52,4.374 false 1.053,4.05 1.313,4.374 false

Apply battery voltage to the door lock motor and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)
Unlock


If the result is not as specified, replace the rear door lock assembly.

Text in Illustration
*a Component without harness connected
(Rear Door Lock Assembly LH)
*b Lock
*c Unlock



b.

Check the detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (LSSR) - 9 (E) Lock 10 kΩ or higher
6 (LSSR) - 9 (E) Unlock Below 1 Ω


If the result is not as specified, replace the rear door lock assembly.



Hide 69050A 2.INSPECT REAR DOOR LOCK ASSEMBLY RH

a.

Check the door lock motor operation.

i.
B164416E07
0.116,0.204 0.606,0.423 0.489,0.218 10 *a 2.488,3.882 2.811,4.052 0.323,0.170 10 *c 1.921,3.882 2.124,4.038 0.203,0.156 10 *b 0.179,3.655 0.275,3.797 0.097,0.142 10 L 0.532,4.308 0.656,4.450 0.125,0.142 10 E 0.976,4.308 1.364,4.450 0.389,0.142 10 LSSR 1.416,3.655 1.624,3.797 0.208,0.142 10 UL 0.682,4.06 0.593,4.308 false 1.066,4.054 1.165,4.308 false 1.156,3.865 1.416,3.732 false 0.546,3.87 0.277,3.745 false

Apply battery voltage to the door lock motor and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)
Unlock


If the result is not as specified, replace the rear door lock assembly.

Text in Illustration
*a Component without harness connected
(Rear Door Lock Assembly RH)
*b Unlock
*c Lock



b.

Check the detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (LSSR) - 9 (E) Lock 10 kΩ or higher
6 (LSSR) - 9 (E) Unlock Below 1 Ω


If the result is not as specified, replace the rear door lock assembly.