METER GAUGE AND WARNING/INDICATOR
| *A | for Optitron meter | *B | for Analog meter |
| *1 | Tachometer | *2 | Speedometer |
| *3 | Multi-information display
·
Shift indicator ·
Eco driving indicator zone display ·
ODO/TRIP meter ·
Average fuel consumption |
*4 | Voltage meter |
| *5 | Fuel receiver gauge | *6 | Engine coolant temperature receiver gauge |
| Item | Details |
|---|---|
| Tachometer | The combination meter receives an engine speed signal from the ECM and the gauge needle operates (CAN). |
| Speedometer | Based on a signal received from the wheel speed sensors, the master cylinder solenoid (skid control ECU) calculates the vehicle speed and transmits data to the combination meter (CAN). |
| ODO/TRIP meter | ·
The combination meter receives a vehicle speed pulse integration signal from the master cylinder solenoid (skid control ECU) and the ODO/TRIP meter display operates (CAN). ·
The ODO/TRIP meter display changes when the ODO/TRIP switch is operated. |
| Fuel receiver gauge | The combination meter receives fuel amount information measured by the fuel sender gauge and the gauge needle operates (Direct line). |
| Engine coolant temperature gauge | The combination meter receives an engine coolant temperature signal from the ECM, and the gauge needle operates (CAN). |
| Voltage meter (for Optitron Meter) | Monitors IG voltage and the gauge needle operates (Direct line). |
| Item | Details |
|---|---|
High beam indicator light
|
Receives BEAM indicator light signals from the main body ECU (CAN). |
Front fog indicator light
|
The indicator turns on when a FRONT FOG illumination command signal is received (CAN). |
SRS warning light
|
Receives malfunction signals from the center airbag sensor (CAN). |
Driver side seat belt warning light
|
Receives driver seat belt signals (unfastened) from the main body ECU (CAN). |
Brake warning light
|
·
Comes on when the parking brake switch is on (CAN). ·
Brake fluid level warning switch is ON (Direct line). ·
Vehicle stability control system is malfunctioning. |
CHARGE warning light
|
Receives malfunction signals from the generator (Direct line and CAN). |
ABS warning light
|
Receives malfunction signals from the master cylinder solenoid (skid control ECU) (CAN). |
MIL
|
Receives malfunction signals from the ECM (Direct line). |
Fuel level warning light
|
Receives signals from the fuel sender gauge indicating low or no fuel (Direct line). |
SLIP indicator light
|
Receives malfunction signals from the master cylinder solenoid (skid control ECU) (CAN). |
TAIL indicator light
|
The indicator turns on when a taillight illumination signal is received (CAN). |
Turn signal indicator light (LH/RH)
|
Receives a turn signal from the FLASHER relay (Direct line). |
PPS warning light
|
Receives power steering warning signals from the power steering ECU (CAN). |
Eco Driving Indicator Light
|
Receives an Ecology lamp indicator signal from the ECM (CAN (CAN No. 1 Bus)) and illuminates when the vehicle is being driven ecologically. |
Open door warning light
|
Receives door open signals from the main body ECU (CAN). |
Oil pressure warning light
|
Receives a oil pressure sensor signal from the ECM (CAN). |
A/T oil temperature warning light
|
Receives a automatic transmission oil temperature signal from ECM (CAN). |
VSC OFF indicator light
|
Receives a VSC OFF signal from the master cylinder solenoid (skid control ECU) (CAN). |
TRC OFF indicator light
|
Receives a TRC OFF signal from the master cylinder solenoid (skid control ECU) (CAN). |
A-TRAC indicator light*1
|
Receives A-TRAC signal from the master cylinder solenoid (skid control ECU) (CAN). |
AUTO LSD indicator light*2
|
Receives AUTO LSD signal from the master cylinder solenoid (skid control ECU) (CAN). |
Center differential lock indicator light*1, *3
|
Receives a center differential lock switch ON signal from the four wheel drive control ECU (CAN). |
4LO indicator light*6
|
Receives 4LO signals from the 4WD control ECU (CAN). |
Downhill Assist Control indicator light*1
|
Receives Downhill Assist Control indicator signals from the master cylinder solenoid (skid control ECU) (CAN). |
Cruise indicator light*4
|
Receives a cruise control switch signal from the ECM (CAN). |
Set indicator light*4
|
Receives a cruise control switch signal from the ECM (CAN). |
*1: for 4WD
*2: for 2WD
*3: for Optitron Meter
*4: w/ Cruise Control System
MULTI-INFORMATION DISPLAY (for Optitron Meter)
Drive monitor
The information displayed changes in the following order each time the ODO/TRIP switch is pressed.
| *a | ODO | *b | TRIP A
(If the ODO/TRIP switch is pressed for 0.8 seconds or more, the TRIP A display is reset.) |
| *c | TRIP B
(If the ODO/TRIP switch is pressed for 0.8 seconds or more, the TRIP B display is reset.) |
*d | Eco Driving Indicator Zone Display and Average fuel consumption
(If the ODO/TRIP switch is pressed for 0.8 seconds or more, the average fuel consumption display is reset. The average fuel consumption display in the accessory meter is also reset.) |
| *e | Eco Driving Indicator user customize screen.
(If the ODO/TRIP switch is pressed for 0.8 seconds or more, the eco driving indicator is enabled/disabled.) |
- | - |
MULTI-INFORMATION DISPLAY (for Analog Meter)
Drive monitor
The information displayed changes in the following order each time the ODO/TRIP switch is pressed.
| *a | ODO | *b | TRIP A
(If the ODO/TRIP switch is pressed for 0.8 seconds or more, the TRIP A display is reset.) |
| *c | TRIP B
(If the ODO/TRIP switch is pressed for 0.8 seconds or more, the TRIP B display is reset.) |
*d | Eco Driving Indicator Zone Display and Average fuel consumption
(If the ODO/TRIP switch is pressed for 0.8 seconds or more, the average fuel consumption display is reset. The average fuel consumption display in the accessory meter is also reset.) |
| *e | Eco Driving Indicator user customize screen.
(If the ODO/TRIP switch is pressed for 0.8 seconds or more, the eco driving indicator is enabled/disabled.) |
- | - |