METER GAUGE AND WARNING/INDICATOR
| *1 | Tachometer | *2 | Speedometer |
| *3 | Multi-information display
·
Shift indicator ·
Eco driving indicator zone display ·
ODO/TRIP meter ·
Average fuel consumption |
*4 | Fuel receiver gauge |
| *5 | Engine coolant temperature receiver gauge | - | - |
| *1 | Tachometer | *2 | Speedometer |
| *3 | Multi-information display
·
Cruise information display ·
Advisory display ·
Road surface freezing ·
Outside temperature ·
ODO/TRIP meter |
*4 | Fuel receiver gauge |
| *5 | Engine coolant temperature receiver gauge | - | - |
| Item | Details |
|---|---|
| Tachometer | The combination meter receives an engine speed signal from the ECM and the gauge needle operates (CAN). |
| Speedometer | Based on a signal received from the wheel speed sensors, the master cylinder solenoid (skid control ECU) calculates the vehicle speed and transmits data to the combination meter (CAN). |
| ODO/TRIP meter | ·
The combination meter receives a vehicle speed pulse integration signal from the master cylinder solenoid (skid control ECU) and the ODO/TRIP meter display operates (CAN). ·
The ODO/TRIP meter display changes when the ODO/TRIP switch is operated. |
| Fuel receiver gauge | The combination meter receives fuel amount information measured by the fuel sender gauge and the gauge needle operates (Direct line). |
| Engine coolant temperature gauge | The combination meter receives an engine coolant temperature signal from the ECM, and the gauge needle operates (CAN). |
| Item | Details |
|---|---|
Driver and passenger side seat belt warning light
|
Receives driver seat belt signals (unfastened) from the main body ECU (multiplex network body ECU) (CAN). |
Open door warning light
|
Receives door open signals from the main body ECU (multiplex network body ECU) (CAN). |
A/T oil temperature warning light*1
|
Receives a automatic transmission oil temperature signal from ECM (CAN). |
High beam indicator light
|
Receives BEAM indicator light signals from the main body ECU (multiplex network body ECU) (CAN). |
Cruise indicator light
|
Receives a cruise control switch signal from the ECM (CAN). |
Set indicator light
|
Receives a cruise control switch signal from the ECM (CAN). |
Oil pressure warning light
|
Receives a oil pressure sensor signal from the ECM (CAN). |
SRS warning light
|
Receives malfunction signals from the center airbag sensor (CAN). |
MIL
|
Receives malfunction signals from the ECM (Direct line). |
CHARGE warning light
|
Receives malfunction signals from the generator (Direct line and CAN). |
TAIL indicator light
|
The indicator turns on when a taillight illumination signal is received (CAN). |
SLIP indicator light
|
Receives malfunction signals from the master cylinder solenoid (skid control ECU) (CAN). |
VSC OFF indicator light
|
Receives a VSC OFF signal from the master cylinder solenoid (skid control ECU) (CAN). |
AUTO LSD indicator light*2
|
Receives AUTO LSD signal from the master cylinder solenoid (skid control ECU) (CAN). |
A-TRAC indicator light*3
|
Receives A-TRAC signal from the master cylinder solenoid (skid control ECU) (CAN). |
Downhill Assist Control indicator light*3
|
Receives Downhill Assist Control indicator signals from the master cylinder solenoid (skid control ECU) (CAN). |
TRC OFF indicator light
|
Receives a TRC OFF signal from the master cylinder solenoid (skid control ECU) (CAN). |
ABS warning light
|
Receives malfunction signals from the master cylinder solenoid (skid control ECU) (CAN). |
Brake warning light
|
·
Comes on when the parking brake switch is on (CAN). ·
Brake fluid level warning switch is ON (Direct line). ·
Vehicle stability control system is malfunctioning. |
4LO indicator light*3
|
Receives 4LO signals from the 4WD control ECU (CAN). |
Center differential lock indicator light*3, *4
|
Receives a center differential lock switch ON signal from the four wheel drive control ECU (CAN). |
Front fog indicator light
|
The indicator turns on when a FRONT FOG illumination command signal is received (CAN). |
Fuel level warning light
|
Receives signals from the fuel sender gauge indicating low or no fuel (Direct line). |
Turn signal indicator light (LH/RH)
|
Receives a turn signal from the FLASHER relay (Direct line). |
Eco Driving Indicator Light
|
Receives an Ecology lamp indicator signal from the ECM (CAN (CAN No. 1 Bus)) and illuminates when the vehicle is being driven ecologically. |
PPS warning light
|
Receives power steering warning signals from the power steering ECU (CAN). |
Master warning light*4
|
Receives warning signal from each ECU (CAN) |
*1: for Analog Meter
*2: for 2WD
*3: for 4WD
*4: for Optitron Meter
MULTI-INFORMATION DISPLAY (for Analog Meter)
The information displayed changes in the following order each time the ODO/TRIP switch is pressed.
| *a | ODO | *b | TRIP A
(If the ODO/TRIP switch is pressed for 0.8 seconds or more, the TRIP A display is reset.) |
| *c | TRIP B
(If the ODO/TRIP switch is pressed for 0.8 seconds or more, the TRIP B display is reset.) |
*d | Eco Driving Indicator Zone Display and Average fuel consumption
(If the ODO/TRIP switch is pressed for 0.8 seconds or more, the average fuel consumption display is reset. The average fuel consumption display in the accessory meter is also reset.)* |
| *e | Eco Driving Indicator user customize screen.
(If the ODO/TRIP switch is pressed for 0.8 seconds or more, the eco driving indicator is enabled/disabled.) |
- | - |
*: Unit changes depending on the customized setting.
MULTI-INFORMATION DISPLAY (for Optitron Meter)
The information displayed changes in the following order each time the ODO/TRIP switch is pressed.
| *a | ODO | *b | TRIP A
(If the ODO/TRIP switch is pressed for 0.8 seconds or more, the TRIP A display is reset.) |
| *c | TRIP B
(If the ODO/TRIP switch is pressed for 0.8 seconds or more, the TRIP B display is reset.) |
- | - |
The multi-information display flow can be switched as shown in the flow chart below:
| No. | Transition Condition |
|---|---|
| *1 | If the display conditions for 2 or more messages are met, relevant messages are alternately displayed for 2 seconds each. |
| *2 | Conditions are not met and all new messages have been displayed. |
| *3 | If the ignition switch is turned off during the "Opening" display, the "Opening" display will be shown from the beginning. |
| *4 | If the DISP switch is used to change from an advisory message to the cruise information display screen, repeatedly operating the DISP switch will cycle through the cruise information screens and then return the advisory message if the display conditions are still met. |
| *5 | If the DISP switch is not operated for more than 6 seconds with any of the caution or warning message display conditions still met, the relevant caution or warning messages are displayed. |
| Item | Detail | |
|---|---|---|
| Cruise information display | Average fuel consumption | 6 types of information (average fuel consumption, current fuel consumption, cruising range, elapsed time, vehicle speed and steering angle) can be displayed. |
| Current fuel consumption | ||
| Cruising Range | ||
| Elapsed Time | ||
| Vehicle Speed | ||
| Steering Angle | ||
| ECO driving indicator zone display | In addition to the cruise information display, the combination meter assembly indicates the ECO driving indicator zone display. | |
| Setting | Displays the customized setting of each item. | |
| Advisory display | Each system advisory | Interrupts the multi-information display immediately when an advisory occurs. |