Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2013.08
RM1440E _58 Vehicle Interior _056158 METER / GAUGE / DISPLAY _0274083 METER / GAUGE SYSTEM D

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  OPERATION CHECK  


INSPECT INDICATOR/WARNING LIGHT


a.

Check the following indicators and warning lights.

Indicator/Warning Light Switch Condition Specified Condition
SLIP indicator light Ignition switch off → ON Comes on for 3 seconds
VSC OFF indicator light
AUTO LSD indicator light*1
A-TRAC indicator light*2
Downhill Assist Control indicator light*2
TRC OFF indicator light
ABS warning light
BRAKE warning light
Eco Driving Indicator Light
PPS warning light
Master warning light
SRS warning light Ignition switch off → ON Comes on for 6 seconds
A/T TEMP warning light*3 Ignition switch off → ON
·

Illuminates when ignition switch turned to ON

·

Turns off when engine started


OIL PRESSURE warning light
MIL
CHARGE warning light

*1: for 2WD

*2: for 4WD

*3: for Analog meter




INSPECT SPEEDOMETER


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

According to the display on intelligent tester, read the "Data List".

Reference:
Intelligent tester Display ( km/h) Speedometer Display (km/h)
20 21 to 25
40 41.7 to 46.2
60 62.7 to 67.2
80 83.4 to 88.4
100 104.3 to 109.3
120 125.1 to 130.6
140 145.8 to 151.8
160 166.2 to 173.2
180 186.9 to 194.5


If the result is not as specified, the speedometer may have a malfunction.

NOTICE:

Do not use worn, underinflated or overinflated tires, as the speedometer reading will be inaccurate.



f.

Check the deflection width of the speedometer indicator.

Reference:

Within 0.3°




INSPECT TACHOMETER


a.

Connect the intelligent tester, and start the engine.


b.

Compare the test results with the tachometer indicator.

DC 13.5 V, at 25°C (77°F):
Standard Indication (rpm) Acceptable Range
Data in ( ) is for reference
700 630 to 770
1000 (900 to 1100)
2000 (1850 to 2150)
3000 2800 to 3200
4000 (3800 to 4200)
5000 4800 to 5200
6000 (5750 to 6250)


If the result is not as specified, the tachometer may have a malfunction.



INSPECT METER/GAUGE


a.

Connect the intelligent tester to the DLC3.


b.

Perform the Active Test (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

OK:

Each meter/gauge needle indication is normal.




INSPECT WARNING/INDICATOR LIGHT


a.

Connect the intelligent tester to the DLC3.


b.

Perform the Active Test (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

OK:

Each warning/indicator light can be turned on and off using the intelligent tester.




INSPECT MULTI-INFORMATION DISPLAY (for Analog Meter)


a.
E221151

Connect the intelligent tester to the DLC3.


b.

Perform the Active Test (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

HINT:

If this Active Test is being performed and the ignition switch is turned off and then to ON, the clock and ODO/TRIP display background may turn white. If this occurs, end the Active Test and turn the ignition switch off.


OK:

All dots in the multi-information display can be turned on and off using the intelligent tester.




INSPECT MULTI-INFORMATION DISPLAY (for Optitron Meter)


a.
E221150

Connect the intelligent tester to the DLC3.


b.

Perform the Active Test (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

HINT:

If this Active Test is being performed and the ignition switch is turned off and then to ON, the clock and ODO/TRIP display background may turn white. If this occurs, end the Active Test and turn the ignition switch off.


OK:

All dots in the multi-information display can be turned on and off using the intelligent tester.