Home › Vehicle Interior › MIRROR (INT) › INNER REAR VIEW MIRROR › 2010.08–2013.08
RM1440E _58 Vehicle Interior _056159 MIRROR (INT) _0274088 INNER REAR VIEW MIRROR G

MIRROR (INT)  INNER REAR VIEW MIRROR  INSPECTION  


PROCEDURE

Hide 87810 1.INSPECT INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)

a.

w/ Rear Monitor:

B453188E01
2.125,1.417 2.552,1.125 true 2.24,1.469 2.625,1.469 true 1.74,2.927 1.885,2.667 true 1.313,4.281 1.563,4.281 false 1.031,0.615 1.344,0.813 0.313,0.198 10 false *a 2.677,1.385 2.99,1.583 0.313,0.198 10 false IG 1.646,2.927 1.958,3.125 0.313,0.198 10 false A 1.135,4.188 1.448,4.385 0.313,0.198 10 false *1 4.167,1.698 4.479,1.896 0.313,0.198 10 false *b 4.104,2.688 4.417,2.885 0.313,0.198 10 false *c 2.615,1.052 2.927,1.25 0.313,0.198 10 false E

Check operation of the electrochromic mirror.

Text in Illustration
*1 Black-colored Tape
*a Component without harness connected
(Inner Rear View Mirror Assembly)
*b Bright
*c Dark

i.

Connect the positive (+) lead of the battery to terminal 1 and the negative (-) lead to terminal 2.


ii.

Check that the LED labeled A in the illustration is illuminated.


iii.

Attach black-colored tape to the forward sensor to prevent it from sensing light.


iv.

Shine an electric light on the mirror. Check that the mirror surface changes from bright to dark.

HINT:

When the environment is very bright, the antiglare operation may occur immediately after the tape is applied.


If the result is not as specified, replace the inner rear view mirror assembly.



b.

w/o Rear Monitor:

B453189E01
1.5,1.104 1.635,0.844 true 1.875,1.094 1.771,0.844 true 1.677,2.25 1.813,1.99 true 1.25,3.573 1.49,3.573 false 1.115,0.188 1.427,0.385 0.313,0.198 10 false *a 1.333,1.042 1.646,1.24 0.313,0.198 10 false IG 1.906,1.073 2.219,1.271 0.313,0.198 10 false E 1.563,2.25 1.875,2.448 0.313,0.198 10 false A 1.063,3.479 1.375,3.677 0.313,0.198 10 false *1 4.135,1.24 4.448,1.438 0.313,0.198 10 false *b 4.083,2.156 4.396,2.354 0.313,0.198 10 false *c

Check operation of the electrochromic mirror.

Text in Illustration
*1 Black-colored Tape
*a Component without harness connected
(Inner Rear View Mirror Assembly)
*b Bright
*c Dark

i.

Connect the positive (+) lead of the battery to terminal 7 and the negative (-) lead to terminal 6.


ii.

Check that the LED labeled A in the illustration is illuminated.


iii.

Attach black-colored tape to the forward sensor to prevent it from sensing light.


iv.

Shine an electric light on the mirror. Check that the mirror surface changes from bright to dark.

HINT:

When the environment is very bright, the antiglare operation may occur immediately after the tape is applied.


If the result is not as specified, replace the inner rear view mirror assembly.