Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM1440E _58 Vehicle Interior _056160 SUPPLEMENTAL RESTRAINT SYSTEMS _0274089 AIRBAG SYSTEM L

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  PRECAUTION  


CAUTION:
·

This vehicle is equipped with a Supplemental Restraint System (SRS), which consists of a steering pad, instrument panel passenger airbag, curtain shield airbag, front seat side airbag, seat belt pretensioner, center airbag sensor, front airbag sensor, side airbag sensor, rear airbag sensor and rear floor side airbag sensor. Failure to carry out service procedures in the correct sequence could cause SRS parts to unexpectedly deploy and possibly lead to serious injuries. Furthermore, if a mistake is made when servicing SRS parts, they may fail to operate when required. Before performing servicing (including installation/removal, inspection and replacement of parts), be sure to read the following precautions.

·

Before starting work, wait at least 90 seconds after the ignition switch is turned off and after the cable is disconnected from the negative (-) battery terminal (SRS parts are equipped with a backup power source. If work is started within 90 seconds of turning the ignition switch off and disconnecting the cable from the negative (-) battery terminal, SRS parts may deploy).

·

Do not expose SRS parts directly to hot air or flames.



NOTICE:
·

Malfunction symptoms of SRS parts are difficult to confirm. DTCs are the most important source of information when troubleshooting. During troubleshooting, always confirm DTCs before disconnecting the cable from the negative (-) battery terminal.

·

For minor collisions where SRS parts do not deploy, always inspect the SRS parts.

·

Before performing repairs, remove the airbag sensors if any kind of impact is likely to occur to an airbag sensor during repairs.

·

Never use SRS parts from another vehicle. When replacing SRS parts, replace them with new ones.

·

Never disassemble or attempt to repair SRS parts.

·

If an SRS part has been dropped, or if there are any cracks, dents or other defects in the case, bracket or connector, replace the SRS part with a new one.

·

Use an ohmmeter/voltmeter with high impedance (10 kΩ/V minimum) for troubleshooting the electrical circuits.

·

Information labels are attached to the periphery of SRS parts. Follow the cautions and instructions on the labels.

·

After work on the SRS is completed, perform the SRS warning light check (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).

·

When the cable is disconnected from the negative (-) battery terminal, the memory settings of each system are cleared. Because of this, be sure to write down the settings of each system before starting work. When work is finished, reset the settings of each system as before. Never use a backup power supply from outside the vehicle to avoid clearing the memory in a system.

·

If the vehicle is equipped with a mobile communication system, refer to the Precaution in the Introduction section.



HINT:

In the airbag system, the center airbag sensor, front airbag sensor LH and RH, side airbag sensor LH and RH, rear airbag sensor LH and RH, and rear floor side airbag sensor are collectively referred to as the airbag sensors.


HANDLING PRECAUTIONS FOR AIRBAG SENSORS


a.

Before starting the following operations, wait for at least 90 seconds after disconnecting the cable from the negative (-) battery terminal:

i.

Replacement of the airbag sensors.


ii.

Adjustment of the front/rear doors of the vehicle equipped with side airbags and curtain shield airbags (fitting adjustment).



b.

When connecting or disconnecting the airbag sensor connectors, make sure that each sensor is installed in the vehicle.


c.

Do not use airbag sensors which have been dropped during operation or transportation.


d.

Do not disassemble the airbag sensors.



INSPECTION PROCEDURE FOR VEHICLE INVOLVED IN ACCIDENT


a.

When the airbag has not deployed, confirm the DTCs by checking the SRS warning light. If there is any malfunction in the SRS airbag system, perform troubleshooting.


b.

When any of the airbags have deployed, replace the airbag sensors and check the installation condition.



SRS CONNECTORS


a.

SRS connectors are located as shown in the following illustration.

C213786E07
4.917,0.458 6.438,0.688 1.521,0.229 10 false Center Airbag Sensor 0.521,0.542 2.26,0.917 1.74,0.375 10 false Front Seat Side Airbag LH (Side Squib LH) 0.375,1.979 2.344,2.354 1.969,0.375 10 false Curtain Shield Airbag LH (Curtain Shield Squib LH) 0.417,3.438 2.24,3.833 1.823,0.396 10 false Front Seat Outer Belt LH (Front Pretensioner Squib LH) 0.406,4.885 2.292,5.302 1.885,0.417 10 false Front Seat Inner Belt LH (Front Seat Belt Buckle Switch LH) 0.729,7.792 2.167,8.01 1.438,0.219 10 false Side Airbag Sensor LH 0.635,6.344 2.135,6.542 1.5,0.198 10 false Rear Airbag Sensor LH 4.656,1.125 4.802,1.271 0.146,0.146 10 false 3 4.656,1.25 4.771,1.396 0.115,0.146 10 false 4 5.625,1.25 5.74,1.396 0.115,0.146 10 false 2 6.542,1.25 6.688,1.396 0.146,0.146 10 false 4 6.542,1.125 6.688,1.271 0.146,0.146 10 false 3 5.615,1.125 5.76,1.271 0.146,0.146 10 false 1 2.75,0.365 2.948,0.615 0.198,0.25 10 false 5 2.958,0.865 3.125,1.094 0.167,0.229 10 false 6 2.74,1.813 2.927,1.979 0.188,0.167 10 false 7 2.958,2.302 3.156,2.49 0.198,0.188 10 false 8 2.75,3.229 2.969,3.396 0.219,0.167 10 false 9 2.948,3.74 3.146,3.927 0.198,0.188 10 false 10 2.75,4.698 2.969,4.865 0.219,0.167 10 false 11 2.979,5.198 3.177,5.385 0.198,0.188 10 false 12 2.74,6.115 2.958,6.281 0.219,0.167 10 false 13 2.969,6.698 3.167,6.885 0.198,0.188 10 false 14 2.75,7.594 2.969,7.76 0.219,0.167 10 false 15 2.958,8.073 3.156,8.26 0.198,0.188 10 false 16 4.146,7.052 4.365,7.219 0.219,0.167 10 false 17 4.156,7.458 4.354,7.646 0.198,0.188 10 false 18

C216527E03
4.927,0.479 6.448,0.708 1.521,0.229 10 false Center Airbag Sensor 0.729,0.25 2.063,0.625 1.333,0.375 10 false Combination Meter (SRS Warning Light) 0.396,4.24 2.469,4.438 2.073,0.198 10 false Steering Pad (Driver Side Squib) 3.688,4.125 4.594,4.448 0.906,0.323 10 false Spiral Cable Sub-assembly 0.677,2.208 2.177,2.406 1.5,0.198 10 false Front Airbag Sensor LH 3.125,0.896 3.573,1.073 0.448,0.177 10 false (CAN) 4.667,1.125 4.813,1.271 0.146,0.146 10 false 3 4.667,1.25 4.781,1.396 0.115,0.146 10 false 4 5.635,1.25 5.75,1.396 0.115,0.146 10 false 2 6.552,1.25 6.698,1.396 0.146,0.146 10 false 4 6.552,1.125 6.698,1.271 0.146,0.146 10 false 3 5.625,1.125 5.771,1.271 0.146,0.146 10 false 1 2.76,1.865 2.979,2.031 0.219,0.167 10 false 19 2.979,2.656 3.177,2.844 0.198,0.188 10 false 20 2.76,3.625 2.979,3.792 0.219,0.167 10 false 23 2.99,4.448 3.188,4.635 0.198,0.188 10 false 24 4.677,3.948 4.896,4.115 0.219,0.167 10 false 25 4.958,4.469 5.156,4.656 0.198,0.188 10 false 26 3.833,2.417 4.052,2.583 0.219,0.167 10 false 21 4.25,2.406 4.448,2.594 0.198,0.188 10 false 22 3.833,5.948 4.052,6.115 0.219,0.167 10 false 31 4.25,5.948 4.448,6.135 0.198,0.188 10 false 32 3.833,7.76 4.052,7.927 0.219,0.167 10 false 21 4.25,7.76 4.448,7.948 0.198,0.188 10 false 22 2.76,5.427 2.979,5.594 0.219,0.167 10 false 27 2.99,6.292 3.188,6.479 0.198,0.188 10 false 28 2.76,7.219 2.979,7.385 0.219,0.167 10 false 19 2.99,8.083 3.188,8.271 0.198,0.188 10 false 20 0.313,5.635 2.552,6.01 2.24,0.375 10 false Instrument Panel Passenger Airbag (Front Passenger Side Squib) 0.656,7.563 2.198,7.76 1.542,0.198 10 false Front Airbag Sensor RH

C216528E03
0.938,0.76 2.458,0.99 1.521,0.229 10 false Center Airbag Sensor 4.875,1.802 6.615,2.177 1.74,0.375 10 false Front Seat Side Airbag RH (Side Squib RH) 4.927,3.031 6.552,3.406 1.625,0.375 10 false Curtain Shield Airbag RH (Curtain Shield Squib RH) 4.781,4.26 6.719,4.635 1.938,0.375 10 false Front Seat Outer Belt RH (Front Pretensioner Squib RH) 5.021,6.771 6.5,6.99 1.479,0.219 10 false Side Airbag Sensor RH 5.052,5.542 6.552,5.74 1.5,0.198 10 false Rear Airbag Sensor RH 0.552,1.375 0.698,1.521 0.146,0.146 10 false 3 0.542,1.51 0.656,1.656 0.115,0.146 10 false 4 1.469,1.51 1.583,1.656 0.115,0.146 10 false 2 2.469,1.51 2.615,1.656 0.146,0.146 10 false 4 2.469,1.385 2.615,1.531 0.146,0.146 10 false 3 1.469,1.375 1.615,1.521 0.146,0.146 10 false 1 4.375,1.604 4.49,1.771 0.115,0.167 10 false 5 4.104,2.094 4.24,2.281 0.135,0.188 10 false 6 4.365,2.833 4.479,3 0.115,0.167 10 false 7 4.052,3.333 4.25,3.521 0.198,0.188 10 false 8 4.313,4.083 4.531,4.25 0.219,0.167 10 false 9 4.042,4.563 4.24,4.75 0.198,0.188 10 false 10 4.313,5.302 4.531,5.469 0.219,0.167 10 false 13 4.052,8.302 4.25,8.49 0.198,0.188 10 false 30 4.323,6.521 4.542,6.688 0.219,0.167 10 false 15 4.052,5.854 4.25,6.042 0.198,0.188 10 false 14 4.323,7.781 4.542,7.948 0.219,0.167 10 false 29 4.052,7.042 4.25,7.229 0.198,0.188 10 false 16 2.823,6.135 3.042,6.302 0.219,0.167 10 false 17 2.813,6.542 3.01,6.729 0.198,0.188 10 false 18 4.771,8.021 6.74,8.219 1.969,0.198 10 false Rear Floor Side Airbag Sensor

Item Application
Terminal Twin-lock Mechanism Connectors 17, 18, 21, 22, 26, 31, 32
Activation Prevention Mechanism Connectors 2, 4, 5, 7, 25, 32
Half Connection Prevention Mechanism Connectors 5, 7, 17, 22, 26, 32
Connector Position Assurance Mechanism Connectors 14, 16, 20, 30
Connector Lock Mechanism (1) Connectors 10, 24, 28
Connector Lock Mechanism (2) Connectors 2, 4
Improper Connection Prevention Lock Mechanism Connectors 1, 3


b.
Z005953E34
1.021,0.521 1.563,0.698 1.563,0.698 2.344,0.385 false 1.042,1.198 1.427,1.323 1.427,1.323 1.969,1.156 false 1.323,0.688 1.792,0.885 0.469,0.198 10 false Spacer 1.135,1.333 1.667,1.531 0.531,0.198 10 false Housing 2.198,1.833 2.542,2.042 0.344,0.208 10 true Male 0.292,1.771 0.792,1.969 0.5,0.198 10 false Female

All connectors in the SRS, except the seat position sensor connector, are colored yellow to distinguish them from other connectors. These connectors have special functions and are specially designed for the SRS. All SRS connectors use durable gold-plated terminals which are placed in the locations shown below to ensure high reliability.

i.

Terminal twin-lock mechanism:

All connectors with a terminal twin-lock mechanism have a two-piece component consisting of a housing and spacer. This design enables the terminal to be locked securely by two locking devices (the retainer and the lance) to prevent terminals from coming out.


ii.

Activation prevention mechanism:

All connectors with an activation prevention mechanism contain a short spring plate. When these connectors are disconnected, the short spring plate creates a short circuit by automatically connecting the positive (+) and negative (-) terminals of the squib.

C361645E01
1.698,2.667 2.125,2.063 2.125,2.063 1.906,1.292 true 5.448,2.698 5.771,2.021 5.771,2.021 5.51,1.323 true 5.292,2.833 5.396,2.281 5.396,2.281 5.292,2.281 true 1.104,2.771 0.927,2.25 false 1.365,3.865 1.094,3.375 1.094,3.375 1.24,3.854 true 1.844,4.427 1.479,4.01 true 1.323,4.146 1.271,4.385 1.271,4.385 1.167,4.115 false 5.323,4.365 5.323,4.031 false 5,3.823 5.073,3.313 5.073,3.313 4.969,3.313 true 2.052,3.198 1.958,3.01 false 1.031,0.042 3.021,0.25 1.99,0.208 10 false When Connector is Connected 4.302,0.031 6.833,0.292 2.531,0.26 10 false When Connector is Disconnected 2.177,1.969 3.49,2.229 1.313,0.26 10 false Short Spring Plate 5.792,1.927 7.104,2.188 1.313,0.26 10 false Short Spring Plate 0.51,3.24 1.167,3.5 0.656,0.26 10 false Terminal 2.094,3.135 2.75,3.396 0.656,0.26 10 false Housing 3.708,2.198 5.76,2.615 2.052,0.417 10 false Contacting Male Terminal 0.875,4.406 1.844,4.74 0.969,0.333 10 false Connectors 1.896,4.365 3.625,4.625 1.729,0.26 10 false Short Spring Plate Off 0.385,2.146 1.042,2.406 0.656,0.26 10 false Housing 2.063,3.521 2.719,3.781 0.656,0.26 10 false Squib 5.625,3.49 6.281,3.75 0.656,0.26 10 false Squib 3.583,3.219 5.635,3.635 2.052,0.417 10 false Short Spring Plate On 4.865,4.396 5.854,4.74 0.99,0.344 10 false Closed Circuit


iii.

Half connection prevention mechanism:

If the connector is not completely connected, the connector is disconnected by the force of the spring so that no continuity exists.

C150151E21
0.948,0.698 1.115,0.698 1.115,0.698 1.438,1.135 false 1.188,0.333 1.313,0.333 1.313,0.333 1.708,1.031 false 2.281,0.188 2.396,0.188 2.396,0.188 2.344,1.021 false 2.917,0.521 3.052,0.521 3.052,0.521 3.063,0.854 false 3.313,0.188 3.427,0.188 3.427,0.188 3.417,0.979 false 5.969,0.302 5.896,0.302 5.896,0.302 5.917,0.885 false 0.104,0.615 1.052,0.813 0.948,0.198 10 false Locking Part 0.656,0.208 1.271,0.406 0.615,0.198 10 false Stopper 1.458,0.083 2.448,0.281 0.99,0.198 10 false Locking Arm 2.51,0.417 2.979,0.615 0.469,0.198 10 false Slider 2.865,0.094 3.375,0.292 0.51,0.198 10 false Spring 3.646,0.594 5.385,0.792 1.74,0.198 10 false Rebound by Slider (Spring) 6.01,0.198 6.646,0.396 0.635,0.198 10 false Stopper


iv.

Connector position assurance mechanism:

The CPA (yellow part) slides only when the housing lock (white part) is completely engaged, which completes the connector engagement.

H043306E19
2.542,0.75 2.25,0.219 2.25,0.219 2.167,0.219 true 2.167,1.479 1.969,1.479 true 0.51,0.115 2.156,0.313 1.646,0.198 10 false Housing Lock (White Part) 0.854,1.385 1.969,1.583 1.115,0.198 10 true CPA (Yellow Part)


v.

Connector lock mechanism (1):

Locking the connector lock button connects the connector securely.

H101828E25
2.188,1.26 1.771,1.26 false 2.24,0.781 1.771,0.781 false 2.74,0.375 3.104,0.375 false 1.396,0.698 1.792,0.875 0.396,0.177 10 false Claw 1.25,1.177 1.833,1.354 0.583,0.177 10 false Groove 3.146,0.292 3.969,0.469 0.823,0.177 10 false Lock Button


vi.

Connector lock mechanism (2):

Both the primary lock with holder lances and the secondary lock with retainer prevent the connectors from becoming disconnected.

C361651E01
4.281,3.01 4.281,2.813 false 1.073,3.219 1.823,3.219 true 0.823,1.875 0.823,1.677 0.823,1.677 1.188,1.458 true 3.354,0.833 3.604,0.26 3.604,0.26 3.792,0.26 false 3.833,0.177 4.75,0.375 0.917,0.198 10 false Holder 0.646,1.896 1.563,2.094 0.917,0.198 10 false Lance 0.5,3.115 1.417,3.313 0.917,0.198 10 false Retainer 4.031,3.031 4.948,3.229 0.917,0.198 10 false Retainer


vii.

Improper connection prevention lock mechanism:

When connecting the holder, the lever is pushed into the lock position by rotating around the A axis to lock the holder securely.

C361654E01
1,1.177 1.292,0.75 1.292,0.75 1.458,0.75 false 5.344,0.906 5.177,0.24 5.177,0.24 5.021,0.24 true 4.479,1.438 5.427,1.438 true 1.51,0.667 1.667,0.865 0.156,0.198 10 false A 4.896,0.167 5.052,0.365 0.156,0.198 10 false A 4.104,1.354 5.021,1.688 0.917,0.333 10 false Lever