Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM1440E _58 Vehicle Interior _056160 SUPPLEMENTAL RESTRAINT SYSTEMS _0274089 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  Diagnosis Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

DTCs are output by the blinking of the SRS warning light.

HINT:
·

When each warning light continues blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.

·

A DTC output mode signal is transmitted through the CAN communication system to each ECU including the center airbag sensor. Thus, when all systems do not enter DTC output mode, there may be an ECM malfunction.



WIRING DIAGRAM

C218343E01
1.438,2.589 1.747,2.745 0.309,0.156 10 F50 1.441,2.752 1.770,2.908 0.330,0.156 10 ECM 1.441,4.244 1.742,4.449 0.302,0.205 10 F13 1.441,4.427 1.867,4.589 0.427,0.163 10 DLC3 5.757,4.742 6.087,4.905 0.330,0.163 10 F33 5.757,4.917 7.121,5.094 1.364,0.177 10 Center Airbag Sensor 0.543,5.359 2.290,5.529 1.747,0.170 10 : CAN Communication Line 1.122,3.575 1.285,3.752 0.163,0.177 10 4 2.071,3.6 2.276,3.777 0.205,0.177 10 13 1.308,3.698 1.568,3.972 0.260,0.274 10 CG 1.78,3.698 2.151,3.923 0.371,0.225 10 TC 1.581,0.693 1.973,0.876 0.392,0.184 10 CANL 1.567,1.244 1.980,1.393 0.413,0.149 10 CANH 6.05,0.693 6.442,0.876 0.392,0.184 10 CANL 6.05,1.244 6.463,1.393 0.413,0.149 10 CANH 1.777,1.807 2.030,1.969 0.253,0.163 10 TC 2.079,0.553 2.263,0.729 0.184,0.177 10 31 2.079,1.12 2.284,1.297 0.205,0.177 10 32 2.079,1.695 2.291,1.878 0.211,0.184 10 28 5.782,0.55 6.030,0.725 0.248,0.174 10 22 5.763,1.111 6.039,1.350 0.276,0.239 10 13

CAUTION / NOTICE / HINT

NOTICE:

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

Result
Result Proceed to
DTC is output A
DTC is not output B



B

2.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)

A

2.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)
a.
U180944E02
1.813,1.063 2.688,1.521 true 1.563,2.792 2.563,2.844 true 0.271,0.792 0.573,0.958 0.302,0.167 10 false F13 0.104,0.052 0.375,0.219 0.271,0.167 10 false *a 0.094,1.49 0.365,1.656 0.271,0.167 10 false *b 2.594,2.76 3.115,2.927 0.521,0.167 10 false 28 (TC) 0.25,2.292 0.542,2.458 0.292,0.167 10 false F50 2.771,1.427 3.083,1.667 0.313,0.24 10 false TC

Turn the ignition switch off.


b.

Disconnect the F50 connector from the ECM.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F13-13 (TC) - F50-28 (TC) Always Below 1 Ω


Text in Illustration
*a Front view of DLC3
*b Front view of wire harness connector
(to ECM)



OK

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
a.
U180814E02
1.542,1.094 1.146,1.719 true 1.698,0.208 1.917,0.438 0.219,0.229 10 false *a 0.99,1.771 1.26,1.958 0.271,0.188 10 false CG 0.281,1.167 0.708,1.406 0.427,0.24 10 false F13

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F13-4 (CG) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of DLC3



OK

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.
U180945E02
1.604,1.469 2.542,1.583 true 0.073,0.021 0.271,0.198 0.198,0.177 10 false *a 2.615,1.5 3.188,1.813 0.573,0.313 10 false 28 (TC) 0.26,0.979 0.552,1.146 0.292,0.167 10 false F50

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F50-28 (TC) - Body ground Always 1 MΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU