Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM1440E _58 Vehicle Interior _056160 SUPPLEMENTAL RESTRAINT SYSTEMS _0274089 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  SRS Warning Light Remains ON  


DESCRIPTION

The SRS warning light is located in the combination meter.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to ON, and then goes off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

When terminals TC and CG of the DLC3 are connected, DTCs are output by the blinking of the SRS warning light.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the center airbag sensor in case the source voltage drops.

When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.

A malfunction in this circuit is not recorded in the center airbag sensor. The SRS warning light automatically goes off when the source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the center airbag sensor to the combination meter through the CAN communication system.

WIRING DIAGRAM

C175154E13
0.06,0.839 1.054,1.051 0.994,0.211 10 from IG2 Relay 0.06,2.649 1.054,2.860 0.994,0.211 10 from IG2 Relay 1.778,1.007 2.121,1.177 0.343,0.170 10 IGN 1.629,2.779 2.204,2.942 0.575,0.163 10 GAUGE 1.697,3.37 2.233,3.547 0.537,0.177 10 ECU-B 0.465,6.338 3.001,6.515 2.536,0.177 10 : CAN Communication Line 2.906,2.565 3.159,2.769 0.253,0.205 10 17 2.913,3.16 3.124,3.330 0.211,0.170 10 15 2.92,4.155 3.124,4.366 0.205,0.211 10 20 3.158,2.663 3.453,2.846 0.295,0.184 10 +IG 3.158,3.265 3.467,3.463 0.309,0.198 10 B 3.158,4.245 3.453,4.450 0.295,0.205 10 E1 3.654,2.054 4.088,2.196 0.434,0.142 10 CANL 3.647,2.65 4.081,2.813 0.434,0.163 10 CANH 6.151,2.056 6.585,2.198 0.434,0.142 10 CANL 6.151,2.652 6.585,2.815 0.434,0.163 10 CANH 4.131,1.919 4.398,2.088 0.267,0.170 10 2 4.138,2.507 4.364,2.684 0.225,0.177 10 1 5.873,1.928 6.133,2.119 0.260,0.191 10 22 5.873,2.531 6.112,2.714 0.239,0.184 10 13 5.866,3.546 6.078,3.751 0.211,0.205 10 25 5.873,4.138 6.098,4.329 0.225,0.191 10 26 6.151,3.66 6.362,3.816 0.211,0.156 10 E1 6.151,4.263 6.390,4.433 0.239,0.170 10 E2 5.88,0.742 6.059,0.893 0.179,0.151 10 21 6.151,0.849 6.501,1.010 0.350,0.161 10 IG2 3.049,5.599 3.351,5.762 0.302,0.163 10 F14 3.049,5.774 4.821,5.958 1.771,0.184 10 Combination Meter 5.748,5.574 6.085,5.737 0.336,0.163 10 F33 5.748,5.732 7.112,5.937 1.364,0.205 10 Center Airbag Sensor 0.214,3.249 1.046,3.460 0.832,0.211 10 from Battery

CAUTION / NOTICE / HINT

NOTICE:

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

Result
Result Proceed to
DTCs are output A
DTC is not output B



B

2.CHECK BATTERY

A

2.CHECK BATTERY
a.

Measure the voltage of the battery.

Standard voltage:

11 to 14 V




OK

3.CHECK CONNECTORS

NG

REPLACE OR RECHARGE BATTERY

3.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and combination meter.

OK:

The connectors are properly connected.




OK

4.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF CENTER AIRBAG SENSOR)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF CENTER AIRBAG SENSOR)
a.
U149929E03
1.563,1.396 1.229,1.927 true 1.729,1.406 2.104,1.938 true 2.208,1.313 2.573,1.313 true 0.417,0.823 0.729,0.979 0.313,0.156 10 false F33 1.115,1.948 1.365,2.135 0.25,0.188 10 false E2 2.052,1.958 2.281,2.125 0.229,0.167 10 false E1 2.615,1.219 2.906,1.385 0.292,0.167 10 false IG2 1.573,0.198 1.792,0.365 0.219,0.167 10 false *a

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Operate all the components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F33-21 (IG2) - F33-25 (E1) Ignition switch ON 11 to 14 V
F33-21 (IG2) - F33-26 (E2) Ignition switch ON 11 to 14 V


Text in Illustration
*a Rear view of wire harness connector
(to Center Airbag Sensor)



OK

5.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER)

NG

REPLACE INSTRUMENT PANEL WIRE

5.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER)
a.
U180815E02
2.104,1.302 1.906,1.802 true 2.583,1.302 2.917,1.802 true 2.323,1.25 2.74,0.927 true 0.25,1.25 0.552,1.406 0.302,0.156 10 false F14 1.844,1.833 1.979,1.99 0.135,0.156 10 false B 2.885,1.854 3.094,2.01 0.208,0.156 10 false E1 2.771,0.844 3.021,1 0.25,0.156 10 false +IG 1.635,0.354 1.833,0.521 0.198,0.167 10 false *a

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


b.

Disconnect the F14 connector from the combination meter.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F14-17 (+IG) - F14-20 (E1) Ignition switch ON 11 to 14 V
F14-15 (B) - F14-20 (E1) Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter)



OK

6.CHECK SRS WARNING LIGHT (SHORT TO GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK SRS WARNING LIGHT (SHORT TO GROUND)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Connect the connector to the combination meter.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON.


f.

Check the SRS warning light condition.

NOTICE:

Make sure that nobody is in the vehicle.


OK:

After the primary check period, the SRS warning light goes off for approximately 10 seconds and then remains on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.




OK

NG