Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM1440E _58 Vehicle Interior _056160 SUPPLEMENTAL RESTRAINT SYSTEMS _0274089 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1830/57  Short in Curtain Shield Squib RH Circuit  B1831/57  Open in Curtain Shield Squib RH Circuit  B1832/57  Short to GND in Curtain Shield Squib RH Circuit  B1833/57  Short to B+ in Curtain Shield Squib RH Circuit  


DESCRIPTION

The curtain shield squib RH circuit consists of the center airbag sensor and curtain shield airbag RH.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the curtain shield squib RH circuit.

DTC Code DTC Detection Condition Trouble Area
B1830/57 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal 5 times in the curtain shield squib RH circuit during the primary check.

·

A curtain shield squib RH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Curtain shield airbag assembly RH (Curtain shield squib RH)

·

Center airbag sensor assembly


B1831/57 One of the following conditions is met:
·

The center airbag sensor detects an open circuit signal in the curtain shield squib RH circuit for 2 seconds.

·

A curtain shield squib RH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Curtain shield airbag assembly RH (Curtain shield squib RH)

·

Center airbag sensor assembly


B1832/57 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to ground signal in the curtain shield squib RH circuit for 0.5 seconds.

·

A curtain shield squib RH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Curtain shield airbag assembly RH (Curtain shield squib RH)

·

Center airbag sensor assembly


B1833/57 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to B+ signal in the curtain shield squib RH circuit for 0.5 seconds.

·

A curtain shield squib RH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Curtain shield airbag assembly RH (Curtain shield squib RH)

·

Center airbag sensor assembly



WIRING DIAGRAM

U149904E03
0.74,3.208 3.135,3.375 2.396,0.167 10 false Curtain Shield Squib RH 2.052,1.573 2.427,1.76 0.375,0.188 10 false ICR+ 4.771,1.667 5.167,1.854 0.396,0.188 10 false ICR+ 2.073,2.406 2.427,2.594 0.354,0.188 10 false ICR- 4.781,2.521 5.177,2.708 0.396,0.188 10 false ICR- 2.458,1.573 2.604,1.74 0.146,0.167 10 false 1 2.479,2.417 2.635,2.573 0.156,0.156 10 false 2 4.583,1.531 4.698,1.698 0.115,0.167 10 false 5 4.583,2.375 4.708,2.542 0.125,0.167 10 false 6 4.76,4.115 5.083,4.302 0.323,0.188 10 false N1 4.75,4.271 6.198,4.479 1.448,0.208 10 false Center Airbag Sensor 0.74,3.052 1.094,3.208 0.354,0.156 10 false N10

CAUTION / NOTICE / HINT

NOTICE:

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


HINT:

To perform the simulation method, enter check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK CURTAIN SHIELD AIRBAG RH (CURTAIN SHIELD SQUIB RH)
a.
U150089E03
2,2.563 2.448,2.688 false 0.958,1.063 0.958,0.542 0.958,0.542 1.146,0.542 false 1.302,1.292 1.479,1.469 0.177,0.177 10 false C 1.083,1.292 1.219,1.49 0.135,0.198 10 false D 0.51,2.021 0.802,2.177 0.292,0.156 10 false N10 1.677,1.333 1.854,1.51 0.177,0.177 10 false *2 1.646,1.688 1.833,1.865 0.188,0.177 10 false *a 2.5,2.583 2.677,2.76 0.177,0.177 10 false *4 2.479,1.969 2.656,2.146 0.177,0.177 10 false *3 1.813,1.063 1.938,1.24 0.125,0.177 10 false A 1.167,0.438 1.354,0.615 0.188,0.177 10 false *1

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the curtain shield airbag RH.


d.

Connect the black wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the curtain shield airbag RH (curtain shield squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1830, B1831, B1832 or B1833 is not output.


HINT:

Codes other than DTC B1830, B1831, B1832 and B1833 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Curtain Shield Squib RH
*2 Center Airbag Sensor
*3 Connector C
*4 SST
*a Front view of wire harness connector
(to Curtain Shield Squib RH)



OK

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.
C214775E01
1.086,1.564 1.279,1.804 0.193,0.239 10 D 0.881,1.077 1.074,1.244 0.193,0.167 10 *1 1.71,1.627 1.903,1.794 0.193,0.167 10 *2 1.318,1.564 1.530,1.785 0.211,0.221 10 C 1.902,1.26 2.095,1.444 0.193,0.184 10 A

Check that the floor wire connector (on the curtain shield airbag RH side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.


Text in Illustration
*1 Curtain Shield Squib RH
*2 Center Airbag Sensor



OK

3.CHECK FLOOR WIRE (CURTAIN SHIELD AIRBAG RH CIRCUIT)

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (CURTAIN SHIELD AIRBAG RH CIRCUIT)
a.
U150090E03
0.969,1.063 0.969,0.542 0.969,0.542 1.021,0.542 false 1.521,1.063 1.521,0.542 1.521,0.542 1.563,0.542 false 1.521,2.552 1.104,2.74 false 1.813,2.552 2.188,2.74 false 1.292,1.313 1.469,1.49 0.177,0.177 10 false C 1.677,1.313 1.854,1.49 0.177,0.177 10 false B 1.073,1.313 1.208,1.51 0.135,0.198 10 false D 0.521,2.021 0.813,2.177 0.292,0.156 10 false N10 1.885,1.354 2.063,1.531 0.177,0.177 10 false *3 1.594,1.74 1.781,1.917 0.188,0.177 10 false *a 2.698,2.01 2.875,2.188 0.177,0.177 10 false *4 2.031,1.052 2.156,1.229 0.125,0.177 10 false A 1.083,0.458 1.271,0.635 0.188,0.177 10 false *1 1.583,0.458 1.771,0.635 0.188,0.177 10 false *2 0.698,2.667 1.063,2.813 0.365,0.146 10 false ICR+ 2.208,2.667 2.615,2.813 0.406,0.146 10 false ICR-

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N10-1 (ICR+) - Body ground Ignition switch ON Below 1 V
N10-2 (ICR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N10-1 (ICR+) - N10-2 (ICR-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N10-1 (ICR+) - N10-2 (ICR-) Always 1 MΩ or higher
N10-1 (ICR+) - Body ground Always 1 MΩ or higher
N10-2 (ICR-) - Body ground Always 1 MΩ or higher



Text in Illustration
*1 Curtain Shield Squib RH
*2 Floor Wire
*3 Center Airbag Sensor
*4 Connector C
*a Front view of wire harness connector
(to Curtain Shield Squib RH)


OK

4.CHECK CENTER AIRBAG SENSOR

NG

REPLACE FLOOR WIRE

4.CHECK CENTER AIRBAG SENSOR
a.
C146261E94
0.875,1.104 0.875,1.49 false 0.823,1.521 1.021,1.719 0.198,0.198 10 false *1 0.979,1.208 1.104,1.406 0.125,0.198 10 false D 1.094,1.208 1.24,1.396 0.146,0.188 10 false C 1.344,1.531 1.542,1.698 0.198,0.167 10 false *2

Connect the connectors to the curtain shield airbag RH and center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1830, B1831, B1832 or B1833 is not output.


HINT:

Codes other than DTC B1830, B1831, B1832 and B1833 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Curtain Shield Squib RH
*2 Center Airbag Sensor



OK

NG