Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM1440E _58 Vehicle Interior _056160 SUPPLEMENTAL RESTRAINT SYSTEMS _0274089 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1656/38  Seat Belt Buckle Switch LH Circuit Malfunction  


DESCRIPTION

The seat belt buckle switch LH circuit consists of the center airbag sensor and front seat inner belt LH.

DTC B1655/37 is stored when a malfunction is detected in the seat belt buckle switch LH circuit.

DTC Code DTC Detection Condition Trouble Area
B1656/38 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the seat belt buckle switch LH circuit for 2 seconds.

·

A front seat inner belt LH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front seat inner belt assembly LH (Seat belt buckle switch LH)

·

Center airbag sensor assembly



WIRING DIAGRAM

C213926E11
2.419,1.486 2.672,1.711 0.253,0.225 10 2 2.437,3.055 2.558,3.225 0.121,0.170 10 1 1.968,1.236 2.370,1.392 0.401,0.156 10 LBE+ 1.968,3.09 2.349,3.239 0.380,0.149 10 LBE- 5.873,2.957 6.272,3.106 0.399,0.149 10 LBE- 5.873,1.367 6.279,1.536 0.406,0.170 10 LBE+ 5.599,1.479 5.846,1.648 0.246,0.170 10 10 5.599,3.066 5.846,3.236 0.246,0.170 10 18 0.409,3.983 0.759,4.125 0.350,0.142 10 O3 0.409,4.144 1.974,4.293 1.566,0.149 10 Front Seat Inner Belt LH 5.606,3.948 5.867,4.111 0.260,0.163 10 O1 5.606,4.122 6.992,4.299 1.385,0.177 10 Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch to ON.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1656 is not output.


HINT:

Codes other than DTC B1656 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and front seat inner belt LH.

OK:

The connectors are properly connected.




OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and front seat inner belt LH.


b.
C208244E01
0.348,1.815 0.541,1.982 0.193,0.167 10 *1 2.122,1.815 2.315,1.982 0.193,0.167 10 *2

Check that the connectors (on the center airbag sensor side and front seat inner belt LH side) are not damaged.

OK:

The connectors are not deformed or damaged.


Text in Illustration
*1 Front Seat Inner Belt LH
*2 Center Airbag Sensor



OK

4.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH)

NG

REPLACE NO. 2 FLOOR WIRE

4.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH)
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

U150076E03
3.5,1 3.177,1.281 false 3.844,1 4.198,1.281 false 6.198,1.042 5.469,1.302 false 6.24,0.917 6.573,1.344 false 1.229,0.646 1.229,0.219 1.229,0.219 1.385,0.219 false 0.677,0.635 0.813,0.823 0.135,0.188 10 false D 1,0.833 1.208,1.031 0.208,0.198 10 false C 1.323,0.833 1.552,1.042 0.229,0.208 10 false B 1.646,0.625 1.885,0.823 0.24,0.198 10 false A 2.667,0.479 2.938,0.677 0.271,0.198 10 false O3 4.885,0.51 5.115,0.677 0.229,0.167 10 false O1 2.802,1.229 3.229,1.385 0.427,0.156 10 false LBE- 4.25,1.219 4.719,1.396 0.469,0.177 10 false LBE+ 6.615,1.271 7.042,1.448 0.427,0.177 10 false LBE+ 5.125,1.219 5.49,1.396 0.365,0.177 10 false LBE- 0.281,1.333 0.469,1.51 0.188,0.177 10 false *1 1.406,0.135 1.594,0.313 0.188,0.177 10 false *3 1.698,1.365 1.875,1.542 0.177,0.177 10 false *2 3.5,0.094 3.688,0.271 0.188,0.177 10 false *a 4.365,0.583 4.542,0.76 0.177,0.177 10 false *4 5.958,0.073 6.146,0.25 0.188,0.177 10 false *b 6.865,0.583 7.042,0.76 0.177,0.177 10 false *5

Text in Illustration
*1 Front Seat Inner Belt LH *2 Center Airbag Sensor
*3 No. 2 Floor Wire *4 Connector C
*5 Connector B - -
*a Front view of wire harness connector
(to Front Seat Inner Belt LH)
*b Rear view of wire harness connector
(to Center Airbag Sensor)


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O3-2 (LBE+) - Body ground Ignition switch ON Below 1 V
O3-1 (LBE-) - Body ground Ignition switch ON Below 1 V



c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O3-2 (LBE+) - O1-10 (LBE+) Always Below 1 Ω
O3-1 (LBE-) - O1-18 (LBE-) Always Below 1 Ω
O3-2 (LBE+) - Body ground Always 1 MΩ or higher
O3-1 (LBE-) - Body ground Always 1 MΩ or higher




OK

5.CHECK FRONT SEAT INNER BELT LH (SEAT BELT BUCKLE SWITCH)

NG

REPLACE NO. 2 FLOOR WIRE

5.CHECK FRONT SEAT INNER BELT LH (SEAT BELT BUCKLE SWITCH)
a.
C146229E37
0.831,1.558 0.991,1.723 0.160,0.165 10 *1 1.781,1.558 1.946,1.723 0.165,0.165 10 *2

Connect the connectors to the center airbag sensor and the front seat inner belt LH.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1656 is not output.


HINT:

Codes other than DTC B1656 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Seat Inner Belt LH
*2 Center Airbag Sensor



OK

NG

6.REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
6.REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the front seat inner belt LH (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).

HINT:

Perform the inspection using parts from a normally functioning vehicle if possible.




NEXT

7.CHECK CENTER AIRBAG SENSOR
7.CHECK CENTER AIRBAG SENSOR
a.
C146229E37
0.831,1.558 0.991,1.723 0.160,0.165 10 *1 1.781,1.558 1.946,1.723 0.165,0.165 10 *2

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1656 is not output.


HINT:

Codes other than DTC B1656 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Seat Inner Belt LH
*2 Center Airbag Sensor



OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

NG