Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM1440E _58 Vehicle Interior _056160 SUPPLEMENTAL RESTRAINT SYSTEMS _0274089 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B161A/8A  Lost Communication with Front Satellite Sensor Bus  


DESCRIPTION

The front collision sensor circuit (front airbag sensor RH circuit and front airbag sensor LH circuit) is composed of the center airbag sensor assembly, front airbag sensor RH and front airbag sensor LH.

The front airbag sensor RH or front airbag sensor LH detects impacts to the vehicle and sends signals to the center airbag sensor assembly to determine if the airbag should be deployed.

DTC B161A/8A is stored when a malfunction is detected in the front collision sensor circuit (front airbag sensor RH circuit and front airbag sensor LH circuit).

DTC Code DTC Detection Condition Trouble Area
B161A/8A In order to check the operation of the passenger airbag ON/OFF indicator when approximately 6 seconds have elapsed after turning the ignition switch to ON, refer to the table in the previous step.
·

The center airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front collision sensor circuit (front airbag sensor RH circuit and front airbag sensor LH circuit).

·

A front airbag sensor RH malfunction.

·

A front airbag sensor LH malfunction.

·

A center airbag sensor assembly malfunction.


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor RH

·

Front airbag sensor LH

·

Center airbag sensor assembly



WIRING DIAGRAM

C210945E14
0.375,2.208 0.646,2.375 0.271,0.167 10 false A35 0.375,2.375 1.885,2.542 1.51,0.167 10 false Front Airbag Sensor RH 5.563,4.74 5.833,4.906 0.271,0.167 10 false F33 5.563,4.917 6.708,5.25 1.146,0.333 10 false Center Airbag Sensor Assembly 1.271,0.823 1.604,1 0.333,0.177 10 false +SR 3.51,0.854 3.802,1.031 0.292,0.177 10 false FA4 3.51,1.656 3.802,1.833 0.292,0.177 10 false FA4 3.51,3.427 3.802,3.604 0.292,0.177 10 false FA4 3.51,4.229 3.802,4.406 0.292,0.177 10 false FA4 5.323,0.719 5.5,0.875 0.177,0.156 10 false 29 5.323,1.531 5.5,1.688 0.177,0.156 10 false 27 1.729,0.719 1.833,0.865 0.104,0.146 10 false 2 3.583,0.646 3.688,0.792 0.104,0.146 10 false 1 3.583,1.448 3.688,1.594 0.104,0.146 10 false 2 1.271,1.635 1.552,1.813 0.281,0.177 10 false -SR 5.667,0.823 6,1 0.333,0.177 10 false +SR 5.667,1.635 5.948,1.813 0.281,0.177 10 false -SR 1.729,1.531 1.833,1.677 0.104,0.146 10 false 1 0.375,4.76 0.708,4.99 0.333,0.229 10 false A13 0.375,4.927 2.021,5.198 1.646,0.271 10 false Front Airbag Sensor LH 1.271,3.417 1.604,3.594 0.333,0.177 10 false +SL 5.323,3.292 5.5,3.448 0.177,0.156 10 false 30 5.323,4.104 5.5,4.26 0.177,0.156 10 false 28 1.74,3.292 1.844,3.438 0.104,0.146 10 false 2 3.604,3.219 3.708,3.365 0.104,0.146 10 false 3 3.604,4.031 3.708,4.177 0.104,0.146 10 false 4 1.271,4.24 1.552,4.417 0.281,0.177 10 false -SL 5.667,3.417 6,3.594 0.333,0.177 10 false +SL 5.667,4.219 5.948,4.396 0.281,0.177 10 false -SL 1.74,4.104 1.844,4.25 0.104,0.146 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Turn the ignition switch off.

HINT:

If a communication error occurs, DTCs for both the LH and RH sides will be stored simultaneously. To identify the malfunctioning area, turn the ignition switch off and then to ON again.



c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1613 is output A
DTC B1618 is output B
DTCs B1613 and B1618 are not output C

HINT:
·

DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the ignition switch off and then to ON again.

·

Codes other than DTCs B1613/83 and B1618/84 may be output at this time, but they are not related to this check.





C

2.CHECK CENTER AIRBAG SENSOR ASSEMBLY

A

B

2.CHECK CENTER AIRBAG SENSOR ASSEMBLY
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B161A is not output.


HINT:

Codes other than DTC B161A may be output at this time, but they are not related to this check.




OK

NG