Home › Vehicle Interior › SEAT › SEAT HEATER SYSTEM
RM1440E _58 Vehicle Interior _056161 SEAT _0274101 SEAT HEATER SYSTEM G

SEAT  SEAT HEATER SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 87501B 1.INSPECT SEAT HEATER CONTROL SUB-ASSEMBLY LH

a.
U149814E03
1.615,1.365 1.615,1.771 true 2.042,1.375 2.042,1.781 true 1.344,1.063 0.958,1.063 true 1.635,0.333 1.813,0.479 0.177,0.146 10 false b2 0.594,0.99 0.948,1.156 0.354,0.167 10 false SWL 2.01,1.792 2.135,1.979 0.125,0.188 10 false E 1.573,1.792 1.698,1.958 0.125,0.167 10 false B 0.135,0.083 0.313,0.26 0.177,0.177 10 false *a

Disconnect the b2 heater control connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b2-6 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
b2-1 (SWL) - b2-6 (E) Ignition switch ON
Seat heater switch LH off
Below 1 V
Ignition switch ON
Seat heater switch LH on
11 to 14 V
b2-4 (B) - b2-6 (E) Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Seat Heater Control Sub-assembly LH)

If the result is not as specified, there may be a malfunction on the wire harness side.


d.

Connect the b2 heater control connector.


e.
U149784E02
1.115,1.813 1.115,1.708 1.115,1.708 1.573,1.479 true 0.969,1.844 1.26,2 0.292,0.156 10 false THL 0.646,1.229 0.813,1.385 0.167,0.156 10 false b2 0.146,0.104 0.333,0.281 0.188,0.177 10 false *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
b2-5 (THL) - Body ground Ignition switch ON
Seat heater switch LH on, MIN → MAX
Gradual increase between value below 1 V and value from 11 to 14 V


Text in Illustration
*a Component with harness connected
(Seat Heater Control Sub-assembly LH)

If the result is not as specified, the seat heater control may have a malfunction.


Hide 87501A 2.INSPECT SEAT HEATER CONTROL SUB-ASSEMBLY RH

a.
U149815E03
1.615,1.375 1.615,1.781 true 2.052,1.365 2.052,1.771 true 1.344,1.063 0.969,1.063 true 1.646,0.323 1.844,0.469 0.198,0.146 10 false a2 0.552,0.969 0.906,1.135 0.354,0.167 10 false SWR 2.021,1.792 2.146,1.979 0.125,0.188 10 false E 1.521,1.792 1.708,1.958 0.188,0.167 10 false B1 0.135,0.083 0.313,0.26 0.177,0.177 10 false *a

Disconnect the a2 heater control connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a2-6 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
a2-1 (SWR) - a2-6 (E) Ignition switch ON
Seat heater switch RH off
Below 1 V
Ignition switch ON
Seat heater switch RH on
11 to 14 V
a2-4 (B1) - a2-6 (E) Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Seat Heater Control Sub-assembly RH)

If the result is not as specified, there may be a malfunction on the wire harness side.


d.

Connect the a2 heater control connector.


e.
U149785E02
1.115,1.813 1.115,1.708 1.115,1.708 1.573,1.479 true 0.948,1.833 1.26,1.99 0.313,0.156 10 false THR 0.646,1.219 0.844,1.375 0.198,0.156 10 false a2 0.146,0.104 0.333,0.281 0.188,0.177 10 false *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
a2-5 (THR) - Body ground Ignition switch ON
Seat heater switch RH on, MIN → MAX
Gradual increase between value below 1 V and value from 11 to 14 V


Text in Illustration
*a Component with harness connected
(Seat Heater Control Sub-assembly RH)

If the result is not as specified, the seat heater control may have a malfunction.