Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY › 2009.08–2011.10
RM1440E _58 Vehicle Interior _056161 SEAT _0274102 REAR NO. 2 SEAT ASSEMBLY A

SEAT  REAR NO. 2 SEAT ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 79040 1.INSTALL NO. 3 SEAT LEG ASSEMBLY LH

a.

Attach the 4 clips to install the seat cushion under carpet LH to the No. 3 seat leg.


Hide 79304A 2.INSTALL NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH

a.

Using a T45 "TORX" socket wrench, install the seatback frame with the 4 "TORX" bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 79226 3.INSTALL NO. 2 SEAT LOCK CABLE

a.
B240401E03
0.563,2.094 0.385,2.094 false 2.385,2.5 2.021,2.5 false 0.198,2.021 0.354,2.167 0.156,0.146 10 false *1 2.396,2.438 2.563,2.604 0.167,0.167 10 true *2

Twist the cable end in the direction indicated by the arrow to connect it.

Text in Illustration
*1 Clamp
*2 Cable End


b.

Attach the clamp to install the cable.


Hide 78091 4.INSTALL FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY

a.
B240395E03
0.708,1.292 0.375,1.292 false 1.208,1.021 1.208,0.813 1.208,0.813 1.458,0.813 false 3.146,1.698 2.813,1.698 false 3.094,2.5 2.938,2.5 false 1.271,2.167 1.052,2.448 1.052,2.448 0.958,2.448 false 1.458,2.521 1.76,2.521 false 0.188,1.219 0.375,1.396 0.188,0.177 10 false *3 1.125,1.031 1.281,1.167 0.156,0.135 10 false *1 3.156,1.615 3.354,1.792 0.198,0.177 10 false *3 3.104,2.417 3.26,2.552 0.156,0.135 10 false *1 0.781,2.365 0.958,2.563 0.177,0.198 10 false *2 1.281,2.438 1.448,2.615 0.167,0.177 10 true *4

Twist the cable end in the direction indicated by the arrow to connect it.

Text in Illustration
*1 Clamp A
*2 Clamp B
*3 Cable Tie
*4 Cable End


b.

Attach the 2 clamps labeled A to install the cable.


c.

Install the clamp labeled B together with the No. 2 seat lock cable.


d.

Install 2 new cable ties.


Hide 72690A 5.INSTALL REAR SEAT LOCK RELEASE STRAP ASSEMBLY

a.
B240390E03
0.719,1.875 1.146,1.875 1.146,1.875 1.146,1.729 false 1.146,1.885 1.146,2.448 1.146,2.448 1.406,2.448 false 2.385,1.167 2.625,1.167 2.625,1.167 2.625,1.417 false 1.063,1.573 1.208,1.719 0.146,0.146 10 false *2 2.198,1.104 2.365,1.292 0.167,0.188 10 true *1

Twist the cable end in the direction indicated by the arrow to connect it.

Text in Illustration
*1 Cable End
*2 Clamp


b.

Attach the 2 clamps to install the cable.


Hide 72690A 6.INSTALL REAR SEAT LOCK RELEASE STRAP ASSEMBLY (for RH Side)

a.
B240392E03
0.979,2.063 1.24,2.063 false 2.271,2.281 2.406,2.281 false 3.073,1.896 3.208,1.896 false 1.781,1.646 2.302,1.646 false 1.563,2.552 1.375,2.552 1.375,2.552 1.375,2.448 false 0.688,0.365 0.844,0.365 0.844,0.365 0.844,0.615 false 1.25,1.99 1.396,2.146 0.146,0.156 10 false *3 2.417,2.208 2.563,2.365 0.146,0.156 10 false *3 1.302,2.281 1.448,2.438 0.146,0.156 10 false *2 2.313,1.583 2.458,1.74 0.146,0.156 10 false *2 3.24,1.813 3.385,1.969 0.146,0.156 10 false *2 0.5,0.281 0.667,0.448 0.167,0.167 10 true *1

Twist the cable end in the direction indicated by the arrow to connect it.

Text in Illustration
*1 Cable End
*2 Clamp
*3 Cable Tie


b.

Attach the 3 clamps to install the cable.


c.

Install 2 new cable ties.


Hide 71843D 7.INSTALL REAR NO. 2 SEAT OUTER RECLINING COVER RH

a.

Attach the 2 claws and guide to install the cover.


b.

Install the screw.


Hide 71833C 8.INSTALL REAR NO. 2 SEAT INNER RECLINING COVER RH

a.

Attach the 5 claws to install the cover.


Hide 71844A 9.INSTALL REAR NO. 2 SEAT OUTER RECLINING COVER LH

a.

Attach the 2 claws and guide to install the cover.


b.

Install the screw.


Hide 71844C 10.INSTALL REAR NO. 2 SEAT INNER RECLINING COVER LH

a.

Attach the 4 claws to install the cover.


Hide 71697B 11.INSTALL REAR NO. 3 SEAT PROTECTOR LH

a.

Attach the 4 claws to install the 2 protectors.


Hide 71970 12.INSTALL REAR SEAT HEADREST ASSEMBLY

a.

Install the headrest with the 3 nuts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 71987A 13.INSTALL REAR SEAT HEADREST CABLE

a.
B238713E01
1.285,1.543 1.450,1.694 0.165,0.151 10 *2 1.256,1.615 1.153,1.615 1.153,1.615 0.649,1.448 false 1.153,1.615 0.649,1.706 false 2.872,1.125 3.037,1.276 0.165,0.151 10 *1 2.853,1.218 2.741,1.218 2.741,1.218 2.66,0.99 false 0.054,1.809 0.219,1.951 0.165,0.142 10 *1 0.534,1.95 0.336,1.892 0.336,1.892 0.236,1.892 false

Twist the 2 cable ends in the direction indicated by the arrow to connect them.

Text in Illustration
*1 Cable End
*2 Clamp


b.

Attach the 2 clamps to install the cable.


Hide 71970A 14.INSTALL REAR SEAT HEADREST COVER

a.

Attach the 2 claws and guide to install the cover.


b.

Install the 2 screws.


Hide 71587C 15.INSTALL REAR NO. 2 SEATBACK EDGE PROTECTOR

a.

Install the protector to the seatback pad with new tack pins.


Hide 79034 16.INSTALL NO. 3 SEATBACK COVER SUB-ASSEMBLY LH

a.
B453539E01
1.708,3.917 1.594,3.135 1.594,3.135 1.792,3.135 false 1.854,3.063 2.167,3.26 0.313,0.198 10 false *1

Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.

Text in Illustration
*1 Hog Ring Pliers

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




Hide 17.INSTALL SEATBACK COVER WITH PAD

a.

Attach the 8 clips.


b.

Attach the hooks to install the seatback cover with pad.


Hide 71865 18.INSTALL REAR SEAT NO. 1 COVER BEZEL

a.

Pass the strap through the bezel hole.


b.

Attach the guide to install the bezel.


c.

Install the 2 screws.


Hide 72635B 19.INSTALL REAR SEATBACK LOCK HOOK

a.

Install the lock hook.


Hide 71702C 20.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH

a.

Attach the 7 clips to install the board.


Hide 72690 21.INSTALL REAR SEAT LOCK RELEASE LEVER ASSEMBLY

a.
B240111E01
0.82,1.892 0.969,2.031 0.149,0.139 10 *4 1.965,1.739 1.965,1.965 1.965,1.965 0.992,1.965 false 1.523,1.864 1.523,1.965 false 1.564,0.141 1.716,0.280 0.152,0.139 10 *1 1.383,0.788 1.802,0.788 false 1.647,0.79 1.647,0.311 false 0.481,1.228 0.633,1.367 0.152,0.139 10 *2 0.661,1.303 1.45,1.303 false 2.904,1.314 3.057,1.453 0.152,0.139 10 *3 1.95,1.389 2.876,1.389 false

Twist the 2 cable ends in the direction indicated by the arrow to connect them.

Text in Illustration
*1 Cable End
*2 No. 2 Seat Lock Cable
*3 Fold Seat Lock Control Cable
*4 Clamp


b.

Attach the 2 clamps.


c.

Attach the hook to install the lever.


d.

Install the 2 screws.


Hide 72615G 22.INSTALL REAR NO. 2 SEATBACK LOCK STRIKER COVER

a.
B240125E01
1.122,0.652 1.278,0.791 0.156,0.140 10 *1 1.66,0.951 1.394,0.739 1.394,0.739 1.288,0.739 false

Attach the guide and claw to install the cover.

Text in Illustration
*1 Guide


Hide 66310F 23.INSTALL ROPE HOOK ASSEMBLY

a.

Install the rope hook with the bolt.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


b.
B240404

Attach the 2 claws to close the cover.


Hide 72058B 24.INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH

a.
B240109E06
0.385,0.688 0.49,0.688 0.49,0.688 0.49,0.833 false 1.771,1.156 1.875,1.156 1.875,1.156 1.875,1.417 false 0.885,0.5 0.885,0.323 0.885,0.323 0.792,0.323 false 0.198,0.604 0.365,0.75 0.167,0.146 10 true *1 1.583,1.063 1.771,1.24 0.188,0.177 10 false *3 0.625,0.24 0.802,0.406 0.177,0.167 10 true *2

Twist the cable end in the direction indicated by the arrow to connect it.

Text in Illustration
*1 Clamp
*2 Cable End
*3 Guide


b.

Attach the clamp.


c.

Attach the guide to install the lever.


d.

Install the 2 screws.


Hide 72615H 25.INSTALL REAR NO. 1 SEATBACK LOCK STRIKER COVER

a.
B240405E01
2.041,0.55 2.193,0.692 0.152,0.142 10 *1 1.587,0.928 1.931,0.627 1.931,0.627 2.026,0.627 false

Attach the guide and claw to install the cover.

Text in Illustration
*1 Guide


Hide 72695C 26.INSTALL REAR SEAT LOCK CONTROL CABLE LH

a.
B240107E03
1.344,2.115 1.521,2.115 false 2.333,3.042 2.438,3.042 2.438,3.042 2.438,2.823 false 1.531,2.021 1.677,2.167 0.146,0.146 10 false *1 2.167,2.958 2.313,3.104 0.146,0.146 10 false *2

Twist the cable end in the direction indicated by the arrow to connect it.

Text in Illustration
*1 Clamp
*2 Cable End


b.

Attach the clamp to install the cable.


Hide 71693D 27.INSTALL REAR SEAT CUSHION INNER HINGE COVER LH

a.

Attach the guide to install the cover.


b.

Install the clip and screw.


Hide 71693D 28.INSTALL REAR SEAT CUSHION INNER HINGE COVER RH

a.

Attach the guide to install the cover.


b.

Install the clip and screw.


Hide 79384A 29.INSTALL REAR NO. 3 SEAT LEG COVER LH

a.

Attach the 2 claws to install the cover.


Hide 79384 30.INSTALL REAR SEAT LEG COVER LH

a.

Attach the 5 clips and 3 hooks to install the cover.


b.

Install the clip.


Hide 72241B 31.INSTALL SEAT TRACK LOCK LEVER

a.

Attach the 2 guides.


b.

Install the lever with the screw.


c.
B240105E01
1.145,1.351 1.301,1.496 0.156,0.145 10 *2 1.738,1.424 1.338,1.424 false 1.764,0.5 1.919,0.645 0.156,0.145 10 *1 1.953,0.586 2.077,0.586 2.077,0.586 1.922,1.187 false

Twist the cable end in the direction indicated by the arrow to connect it.

Text in Illustration
*1 Cable End
*2 Clamp


d.

Attach the clamp.


Hide 72906 32.INSTALL 3RD SEAT LINK SUB-ASSEMBLY LH

a.

Attach the 4 guides and 2 claws to install the link.


b.

Install the 3 clips.


Hide 79202 33.INSTALL NO. 2 SEAT CUSHION FRAME SUB-ASSEMBLY LH

a.

Using a T40 "TORX" socket wrench, install the seat cushion frame with the 4 "TORX" bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


b.

Pull out the seat cushion frame.


Hide 71827B 34.INSTALL REAR NO. 2 SEAT CUSHION MOULDING

a.

Attach the 2 claws to install the moulding.


b.

Install the 2 screws.


Hide 71537B 35.INSTALL REAR NO. 2 SEAT CUSHION PROTECTOR

a.

Install the protector to the seat cushion pad with new tack pins.


Hide 79031 36.INSTALL NO. 3 SEAT CUSHION COVER SUB-ASSEMBLY LH

a.
B238853E01
2.629,2.017 2.794,2.164 0.165,0.147 10 *1 2.021,2.872 1.754,2.872 1.754,2.872 1.858,3.695 false 2.119,1.299 2.119,2.099 2.119,2.099 2.61,2.099 false 2.042,2.791 2.207,2.937 0.165,0.147 10 *2

Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

Text in Illustration
*1 Fastener
*2 Hog Ring Pliers

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




b.

Attach the fastener.


Hide 37.INSTALL SEAT CUSHION COVER WITH PAD

a.

Attach the 2 hooks to install the seat cushion cover with pad.


b.

Attach the 2 hooks.


c.

Install the 2 clips to close the cover.


d.

Close the 2 fasteners.


e.

Attach the 2 fasteners.


Hide 71827B 38.INSTALL REAR NO. 1 SEAT CUSHION MOULDING

a.

Attach the 4 guides and 2 claws to install the moulding.


b.

Install the 2 clips.


Hide 73590 39.INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY LH

Hide 71693 40.INSTALL REAR SEAT LOWER CUSHION HINGE COVER RH

a.

Attach the guide and 2 claws to install the cover.


b.

Install the 2 screws.


Hide 71694 41.INSTALL REAR SEAT LOWER CUSHION HINGE COVER LH

a.

Attach the 3 claws to install the cover.


b.

Install the 2 screws.


Hide 62476E 42.INSTALL REAR SEAT CAP

a.

Install the 2 caps.