Wear protective gloves. Sharp areas on the parts may injure your hands.
71324B
1.REMOVE REAR SEAT CUSHION
Remove the 2 screws and 2 cushions.
71695
2.REMOVE REAR SEATBACK PROTECTOR
Remove the 2 screws.
Detach the 2 hooks and remove the protector.
72927
3.REMOVE REAR SEAT CUSHION UNDER COVER RH
Using a moulding remover, detach the hooks and remove the cover.
4.REMOVE SEAT CUSHION COVER WITH PAD
Disconnect the seat cushion band from the seat cushion cover.
Detach the hooks and remove the seat cushion cover with pad.
79117B
5.REMOVE NO. 1 SEAT CUSHION COVER RH
Cut off the tack pins and remove the cover from the cushion pad.
| *1 | Tack Pin |
71075S
6.REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER RH
Remove the hog rings and seat cushion cover from the seat cushion pad.
71393
7.REMOVE REAR SEAT CUSHION BAND
Remove the band as shown in the illustration.
79956
8.REMOVE REAR SEAT LEG BRACKET COVER
Using a moulding remover, detach the 4 claws and remove the cover.
Use the same procedure for both covers.
79959
9.REMOVE REAR SEAT LEG COVER
Detach the claw and guide, and then remove the cover.
Use the same procedure for both covers.
79109
10.REMOVE NO. 1 SEATBACK BOARD SUB-ASSEMBLY (for Plastic Seatback Board)
Using a clip remover, detach the 2 clips.
Detach the guide and remove the board.
79109
11.REMOVE NO. 1 SEATBACK BOARD SUB-ASSEMBLY (for Seatback Board with Carpet)
Using a clip remover, detach the 3 clips.
Detach the guide and remove the board.
71879A
12.REMOVE REAR SEAT INNER RECLINING COVER RH
Remove the screw.
Detach the 2 guides and remove the cover.
73460C
13.REMOVE REAR CENTER SEAT INNER BELT ASSEMBLY
71095S
14.REMOVE CENTER SEATBACK COVER SUB-ASSEMBLY
Remove the screw.
Detach the 2 guides and remove the cover.
15.REMOVE CENTER SEATBACK ASSEMBLY
Using a T45 "TORX" socket wrench, remove the "TORX" bolt and bush.
Remove the 2 bolts and center seatback.
71960B
16.REMOVE REAR CENTER SEAT HEADREST ASSEMBLY
Remove the headrest.
71397A
17.REMOVE CENTER SEAT HINGE COVER
Detach the claw and remove the cover.
71369B
18.REMOVE REAR SEATBACK STAY COVER LH
Detach the 3 claws and remove the cover.
71349B
19.REMOVE REAR SEATBACK STAY COVER RH
Using a T45 "TORX" socket wrench, remove the "TORX" bolt, bush and hinge.
Detach the 3 claws and remove the cover.
72830
20.REMOVE REAR CENTER SEAT ARMREST ASSEMBLY
Using a T45 "TORX" socket wrench, remove the 2 "TORX" bolts, 2 bushes and armrest.
Remove the bush.
66990B
21.REMOVE NO. 2 CUP HOLDER ASSEMBLY RH
Remove the 2 cup holders.
72996A
22.REMOVE REAR SEATBACK COVER
Using a screwdriver, detach the 4 claws and remove the cover.
Tape the screwdriver tip before use.
72665B
23.REMOVE REAR SEATBACK LOCK COVER
Using a moulding remover, detach the claw.
Move the cover in the direction of the arrow to detach the clip and 2 guides and remove the cover.
71087
24.REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY
Detach the 4 claws and 3 clips, and then remove the board.
71931A
25.REMOVE REAR SEAT HEADREST SUPPORT
Detach the 4 claws and remove the 2 supports.
71413
26.REMOVE REAR NO. 1 SEAT NO. 2 SIDE PLATE
Remove the 2 screws.
Using a moulding remover, detach the 3 claws and remove the plate.
72650A
27.REMOVE REAR SEAT LOCK ASSEMBLY RH
Detach the clamp and disconnect the wire.
Remove the 2 bolts and lock.
72067
28.REMOVE REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY RH
Remove the 2 screws and control lever.
72987
29.REMOVE REAR CENTER SEAT ARMREST COVER
Remove the screw.
Detach the 2 claws and remove the cover.
72665
30.REMOVE REAR SEATBACK LOCK COVER RH
Remove the 2 screws.
Detach the 2 guides and remove the cover.
72630C
31.REMOVE REAR SEATBACK LOCK ASSEMBLY RH
Remove the 2 hog rings.
Remove the 2 bolts.
While moving the release button in the direction of the arrow in the illustration, detach it from the grommet and remove the seatback lock.
72661C
32.REMOVE REAR SEATBACK LOCK RELEASE BUTTON
Remove the release button as shown in the illustration.
|
Counterclockwise |
72646
33.REMOVE REAR SEATBACK STOP BUTTON GROMMET
Detach the 3 claws and remove the grommet.
71931B
34.REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
Detach the 4 claws and remove the 2 supports.
73178A
35.REMOVE SEAT BELT ANCHOR COVER CAP
Using a screwdriver, detach the 2 claws and 2 guides, and then remove the cap.
Tape the screwdriver tip before use.
| *1 | Protective Tape |
73373
36.REMOVE REAR SEAT SHOULDER BELT COVER
Remove the screw.
Detach the 3 claws and remove the cover.
Disconnect the outer belt from the cover.
72618
37.REMOVE REAR SEATBACK LOCK STRIKER PROTECTOR
Remove the protector from the striker.
72613B
38.REMOVE REAR SEAT LOCK STRIKER
Using a T45 "TORX" socket wrench, remove the striker.
39.REMOVE SEATBACK COVER WITH PAD
Remove the hog rings, detach the hook, and then remove the seatback cover with pad.
| *1 | Hook |
| *2 | Hog Ring |
Disconnect the outer belt from the seatback cover with pad.
71077S
40.REMOVE SEPARATE TYPE REAR SEATBACK COVER RH
Remove the hog rings and cover from the seatback pad.
71587A
41.REMOVE REAR SEATBACK EDGE PROTECTOR
Remove the protector from the seatback frame.
73187A
42.REMOVE REAR SEAT SHOULDER BELT GUIDE
Detach the claw and guide, and then remove the belt guide.
73360C
43.REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH
71695B
44.REMOVE REAR NO. 1 SEAT PROTECTOR LH
Detach the 2 claws and remove the protector.
71695C
45.REMOVE REAR NO. 1 SEAT PROTECTOR
Detach the claw and remove the protector.