Wear protective gloves. Sharp areas on the parts may injure your hands.
71846A
1.REMOVE REAR SEAT UPPER RECLINING COVER LH
Using a screwdriver, detach the 3 claws and remove the cover.
Tape the screwdriver tip before use.
| *1 | Protective Tape |
72526A
2.REMOVE RECLINING ADJUSTER RELEASE HANDLE LH
Remove the 3 screws and handle.
71395B
3.REMOVE CENTER SEAT HINGE COVER RH
Using a clip remover, remove the clip.
Detach the 2 guides and remove the cover.
71826B
4.REMOVE REAR SEAT CUSHION MOULDING LH
Using a clip remover, detach the clip.
Using a moulding remover, detach the 3 claws.
Move the moulding in the direction of the arrow to detach the guide and remove the moulding.
72616A
5.REMOVE REAR SEATBACK LOCK STRIKER COVER LH
Using a clip remover, detach the 3 clips and remove the cover.
6.REMOVE SEAT CUSHION COVER WITH PAD
Detach the hooks.
Detach the hook and remove the seat cushion cover with pad.
71696
7.REMOVE REAR NO. 2 SEAT PROTECTOR
Remove the 2 protectors from the cushion pad.
71076S
8.REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER
Remove the hog rings and seat cushion cover from the seat cushion pad.
71647
9.REMOVE REAR SEAT CUSHION EDGE PROTECTOR
Remove the protector from the cushion spring.
10.REMOVE CENTER SEATBACK ASSEMBLY
Remove the 2 bolts and center seatback.
71960B
11.REMOVE REAR SEAT CENTER HEADREST ASSEMBLY
Remove the headrest.
71397A
12.REMOVE CENTER SEAT HINGE COVER
Using a clip remover, remove the clip.
Detach the 2 guides and remove the cover.
72732
13.REMOVE REAR SEAT RECLINING BRACKET LH
Using a T45 "TORX" socket wrench, remove the "TORX" bolt, bush and bracket.
72731
14.REMOVE REAR SEAT RECLINING BRACKET RH
Using a T45 "TORX" socket wrench, remove the "TORX" bolt, bush and bracket.
71369B
15.REMOVE REAR SEATBACK STAY COVER LH
Using a moulding remover, detach the 3 claws.
Detach the guide and remove the cover.
71349B
16.REMOVE REAR SEATBACK STAY COVER RH
Using a moulding remover, detach the 3 claws.
Detach the guide and remove the cover.
72830
17.REMOVE REAR SEAT CENTER ARMREST ASSEMBLY
Using a T45 "TORX" socket wrench, remove the 2 "TORX" bolts and 2 bushes.
Remove the nut and armrest support.
Remove the armrest as shown in the illustration.
72806B
18.REMOVE REAR SEAT CENTER ARMREST CUP HOLDER SUB-ASSEMBLY
Remove the 2 screws.
Using a moulding remover, detach the 2 claws and remove the cup holder.
72996A
19.REMOVE REAR SEATBACK COVER
Using a screwdriver, detach the 4 claws and remove the cover.
Tape the screwdriver tip before use.
72665B
20.REMOVE REAR SEATBACK LOCK COVER
Using a moulding remover, detach the claw.
Move the cover in the direction of the arrow to detach the clip and 2 guides, and then remove the cover.
71087
21.REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY
Using a clip remover, detach the 5 clips and remove the board.
72877C
22.REMOVE SEAT ARMREST COVER
Detach the hooks.
Remove the cover with pad.
Remove the cover from the pad.
71931A
23.REMOVE REAR SEAT HEADREST SUPPORT
Detach the 4 claws and remove the 2 supports.
79157
24.REMOVE NO. 1 SEATBACK COVER
Using a moulding remover, detach the 2 claws.
Detach the guide and remove the cover.
72660F
25.REMOVE REAR SEAT LOCK ASSEMBLY LH
Detach the clamp and disconnect the wire.
Remove the 2 bolts and lock.
72663
26.REMOVE REAR NO. 1 SEAT LOCK CONTROL LEVER
Remove the lever as shown in the illustration.
79873
27.REMOVE FOLD SEATBACK WIRE
Detach the 2 claws and remove the wire.
74633A
28.REMOVE COAT HOOK CAP
Using a screwdriver, detach the 2 claws and guide, and then remove the cap.
Tape the screwdriver tip before use.
| *1 | Protective Tape |
72978
29.REMOVE CENTER NO. 2 SEATBACK COVER
Remove the 3 screws and cover.
73390C
30.REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH
Remove the bolt and inner belt, and disconnect the center outer belt.
72572C
31.REMOVE RECLINING ADJUSTER KNOB CAP LH
Using a screwdriver, detach the claw and guide, and then remove the cap.
Tape the screwdriver tip before use.
| *1 | Protective Tape |
72058A
32.REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH
Remove the 2 screws.
Disconnect the cable in the order shown in the illustration and remove the lever.
73178A
33.REMOVE SEAT BELT ANCHOR COVER CAP
Using a screwdriver, detach the 2 claws and remove the cap.
Tape the screwdriver tip before use.
| *1 | Protective Tape |
73373
34.REMOVE REAR SEAT SHOULDER BELT COVER
Detach the 2 claws and 2 guides, and then remove the cover.
Disconnect the outer belt from the cover.
72996A
35.REMOVE REAR SEATBACK COVER
Using a screwdriver, detach the 4 claws and remove the cover.
Tape the screwdriver tip before use.
71890A
36.REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY LH
Using a clip remover, detach the 7 clips and remove the carpet.
71931B
37.REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
Detach the 4 claws and remove the 2 supports.
38.REMOVE SEATBACK COVER WITH PAD
Remove the hog rings and detach the hooks, and then remove the seatback cover with pad.
| *1 | Hook |
| *2 | Hog Ring |
Disconnect the outer belt from the seatback cover with pad.
71078S
39.REMOVE SEPARATE TYPE REAR SEATBACK COVER
Remove the hog rings and cover from the seatback pad.
71587A
40.REMOVE REAR SEATBACK EDGE PROTECTOR
Remove the protector from the seatback frame.
71879A
41.REMOVE REAR SEAT INNER RECLINING COVER LH
Remove the 2 screws.
Detach the guide and remove the cover.
71876J
42.REMOVE RECLINING ADJUSTER INSIDE COVER LH
Remove the 2 screws.
Detach the 2 claws and remove the cover.
71828B
43.REMOVE REAR SEAT REAR CUSHION MOULDING LH
Using a clip remover, detach the clip.
Using a moulding remover, detach the 4 claws.
Move the moulding in the direction of the arrow to detach the guide and remove the moulding.
73949
44.REMOVE CAP
Detach the 2 claws and remove the cap.
71879B
45.REMOVE REAR SEAT RECLINING COVER INNER LH
Detach the claw and guide, and then remove the cover.
71499D
46.REMOVE REAR SEATBACK SPRING DAMPER
Remove the 2 nuts and damper.
73187A
47.REMOVE REAR SEAT SHOULDER BELT GUIDE
Detach the claw and guide, and then remove the belt guide.
73320A
48.REMOVE NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH
72704A
49.REMOVE REAR SEAT RECLINING CONTROL CABLE
Cut off the 4 cable ties.
Detach the 3 cable clamps and disconnect the cable, and then remove the cable.
72704B
50.REMOVE REAR NO. 2 SEAT RECLINING CONTROL CABLE
Detach the 3 cable clamps and disconnect the cable, and then remove the cable.
72068
51.REMOVE REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY LH
Remove the 2 nuts and lever.
71018
52.REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY LH
Using a T45 "TORX" socket wrench, remove the 2 "TORX" bolts.
Remove the 2 bolts and seatback frame.
71016A
53.REMOVE REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH
Remove the 6 nuts and seat cushion frame.
72173B
54.REMOVE REAR SEAT TRACK ADJUSTING HANDLE LH
Slide the slide rail to the rearmost position.
Using a small screwdriver, push down the handle stopper to detach the claw and remove the adjusting handle.
Insert the screwdriver into the hole shown in the illustration while looking into the hole.