Wear protective gloves. Sharp areas on the parts may injure your hands.
71846A
1.REMOVE REAR SEAT UPPER RECLINING COVER LH
Using a screwdriver, detach the 3 claws and remove the rear seat upper reclining cover LH.
Tape the screwdriver tip before use.
| *1 | Protective Tape |
72526A
2.REMOVE RECLINING ADJUSTER RELEASE HANDLE LH
Remove the 3 screws and reclining adjuster release handle LH.
71395B
3.REMOVE CENTER SEAT HINGE COVER RH
Using a clip remover, remove the clip.
Move the center seat hinge cover RH in the direction of the arrow to detach the 2 guides and remove the center seat hinge cover RH.
71826B
4.REMOVE REAR SEAT CUSHION MOULDING LH
Using a clip remover, detach the clip.
Using a moulding remover, detach the 3 claws.
Move the rear seat cushion moulding LH in the direction of the arrow to detach the guide and remove the rear seat cushion moulding LH.
72616A
5.REMOVE REAR SEATBACK LOCK STRIKER COVER LH
Using a clip remover, detach the 3 clips and remove the rear seatback lock striker cover LH.
6.REMOVE SEAT CUSHION COVER WITH PAD
Detach the hooks.
Detach the hook and remove the seat cushion cover with pad.
71696
7.REMOVE REAR NO. 2 SEAT PROTECTOR
Remove the 2 rear No. 2 seat protectors from the separate type rear seat cushion pad.
71076S
8.REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER
Remove the hog rings and separate type rear seat cushion cover from the separate type rear seat cushion pad.
71647
9.REMOVE REAR SEAT CUSHION EDGE PROTECTOR
Remove the rear seat cushion edge protector from the rear seat cushion frame sub-assembly LH.
10.REMOVE CENTER SEATBACK ASSEMBLY
Remove the 2 bolts and center seatback assembly.
71960B
11.REMOVE REAR SEAT CENTER HEADREST ASSEMBLY
Remove the rear seat center headrest assembly.
71397A
12.REMOVE CENTER SEAT HINGE COVER
Using a clip remover, remove the clip.
Move the center seat hinge cover in the direction of the arrow to detach the 2 guides and remove the center seat hinge cover.
72732
13.REMOVE REAR SEAT RECLINING BRACKET LH
Using a T45 "TORX" socket wrench, remove the "TORX" bolt, bush and rear seat reclining bracket LH.
72731
14.REMOVE REAR SEAT RECLINING BRACKET RH
Use the same procedure as for the LH side.
71369B
15.REMOVE REAR SEATBACK STAY COVER LH
Using a moulding remover, detach the 3 claws.
Detach the guide and remove the rear seatback stay cover LH.
71349B
16.REMOVE REAR SEATBACK STAY COVER RH
Use the same procedure as for the LH side.
72830
17.REMOVE REAR SEAT CENTER ARMREST ASSEMBLY
Using a T45 "TORX" socket wrench, remove the 2 "TORX" bolts.
| *1 | Bush |
| *2 | Washer |
| *3 | Wave Washer |
Remove the 2 bushes, washer and wave washer.
Remove the nut and rear center seat armrest support LH.
Remove the rear seat center armrest assembly as shown in the illustration.
72806B
18.REMOVE REAR SEAT CENTER ARMREST CUP HOLDER SUB-ASSEMBLY
Remove the 2 screws.
Using a moulding remover, detach the 2 claws and remove the rear seat center armrest cup holder sub-assembly.
72996A
19.REMOVE REAR SEATBACK COVER
Using a screwdriver, detach the 4 claws and remove the rear seatback cover.
Tape the screwdriver tip before use.
72665B
20.REMOVE REAR SEATBACK LOCK COVER
Using a moulding remover, detach the claw.
Move the rear seatback lock cover in the direction of the arrow to detach the clip and 2 guides, and then remove the rear seatback lock cover.
71087
21.REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY
Using a clip remover, detach the 5 clips and remove the rear seatback board sub-assembly.
72877C
22.REMOVE SEAT ARMREST COVER
Detach the hooks.
Remove the seat armrest cover with pad.
Remove the seat armrest cover from the center No. 1 seat cushion pad.
71931A
23.REMOVE REAR SEAT HEADREST SUPPORT
Detach the 4 claws and remove the 2 rear seat headrest supports.
79157
24.REMOVE NO. 1 SEATBACK COVER
Using a moulding remover, detach the 2 claws.
Detach the guide and remove the No. 1 seatback cover.
72660F
25.REMOVE REAR SEAT LOCK ASSEMBLY LH
Detach the clamp and disconnect the fold seatback wire.
Remove the 2 bolts and rear seat lock assembly LH.
72663
26.REMOVE REAR NO. 1 SEAT LOCK CONTROL LEVER
Remove the rear No. 1 seat lock control lever as shown in the illustration.
79873
27.REMOVE FOLD SEATBACK WIRE
Detach the 2 claws and remove the fold seatback wire.
74633A
28.REMOVE COAT HOOK CAP
Using a screwdriver, detach the 2 claws and guide, and then remove the coat hook cap.
Tape the screwdriver tip before use.
| *1 | Protective Tape |
72978
29.REMOVE CENTER NO. 2 SEATBACK COVER
Remove the 3 screws and center No. 2 seatback cover.
73390C
30.REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH
Remove the bolt and rear No. 1 seat inner belt assembly LH, and disconnect the No. 1 seat 3 point type belt assembly LH.
72572C
31.REMOVE RECLINING ADJUSTER KNOB CAP LH
Using a screwdriver, detach the claw and guide, and then remove the reclining adjuster knob cap LH.
Tape the screwdriver tip before use.
| *1 | Protective Tape |
72058A
32.REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH
Remove the 2 screws.
Disconnect the rear No. 2 seat reclining control cable in the order shown in the illustration and remove the rear seat lock control lever sub-assembly LH.
73178A
33.REMOVE SEAT BELT ANCHOR COVER CAP
Using a screwdriver, detach the 2 claws and remove the seat belt anchor cover cap.
Tape the screwdriver tip before use.
| *1 | Protective Tape |
73373
34.REMOVE REAR SEAT SHOULDER BELT COVER
Detach the 2 claws.
Move the rear seat shoulder belt cover in the direction of the arrow to detach the 2 guides, and then remove the rear seat shoulder belt cover.
Disconnect the No. 1 seat 3 point type belt assembly LH from the rear seat shoulder belt cover.
72996A
35.REMOVE REAR SEATBACK COVER
Using a screwdriver, detach the 4 claws and remove the rear seatback cover.
Tape the screwdriver tip before use.
71890A
36.REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY LH
Using a clip remover, detach the 7 clips and remove the rear seatback board carpet assembly LH.
71931B
37.REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
Detach the 4 claws and remove the 2 rear No. 1 seat headrest support assemblies.
38.REMOVE SEATBACK COVER WITH PAD
Remove the hog rings and detach the hooks, and then remove the seatback cover with pad.
| *1 | Hook |
| *2 | Hog Ring |
Disconnect the No. 1 seat 3 point type belt assembly LH from the seatback cover with pad.
71078S
39.REMOVE SEPARATE TYPE REAR SEATBACK COVER
Remove the hog rings and separate type rear seatback cover from the separate type rear seatback pad.
71587A
40.REMOVE REAR SEATBACK EDGE PROTECTOR
Remove the rear seatback edge protector from the rear seatback frame sub-assembly LH.
71879A
41.REMOVE REAR SEAT INNER RECLINING COVER LH
Remove the 2 screws.
Detach the guide and remove the rear seat inner reclining cover LH.
71876J
42.REMOVE RECLINING ADJUSTER INSIDE COVER LH
Remove the 2 screws.
Detach the 2 claws and remove the reclining adjuster inside cover LH.
71828B
43.REMOVE REAR SEAT REAR CUSHION MOULDING LH
Using a clip remover, detach the clip.
Using a moulding remover, detach the 4 claws.
Move the rear seat rear cushion moulding LH in the direction of the arrow to detach the guide and remove the rear seat rear cushion moulding LH.
73949
44.REMOVE CAP
Detach the 2 claws and remove the cap.
71879B
45.REMOVE REAR SEAT RECLINING COVER INNER LH
Detach the claw and guide, and then remove the rear seat reclining cover inner LH.
71499D
46.REMOVE REAR SEATBACK SPRING DAMPER
Remove the 2 nuts and rear seatback spring damper.
73187A
47.REMOVE REAR SEAT SHOULDER BELT GUIDE
Detach the claw and guide, and then remove the rear seat shoulder belt guide.
73320A
48.REMOVE NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH
72704A
49.REMOVE REAR SEAT RECLINING CONTROL CABLE
Cut off the 4 cable ties.
Detach the 3 cable clamps and disconnect the rear seat reclining control cable, and then remove the rear seat reclining control cable.
72704B
50.REMOVE REAR NO. 2 SEAT RECLINING CONTROL CABLE
Detach the 3 cable clamps and disconnect the rear No. 2 seat reclining control cable, and then remove the rear No. 2 seat reclining control cable.
51.REMOVE REAR SEAT RECLINING INNER PROTECTOR
Detach the claw and remove the rear seat reclining inner protector.
72068
52.REMOVE REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY LH
Remove the 2 nuts and rear back lock control lever sub-assembly LH.
71018
53.REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY LH
Using a T45 "TORX" socket wrench, remove the 2 "TORX" bolts.
Remove the 2 bolts and rear seatback frame sub-assembly LH.
71016A
54.REMOVE REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH
Remove the 6 nuts and rear seat cushion frame sub-assembly LH.
72173B
55.REMOVE REAR SEAT TRACK ADJUSTING HANDLE LH
Slide the slide rail to the rearmost position.
Using a small screwdriver, push down the handle stopper to detach the claw and remove the rear seat track adjusting handle LH.
Insert the screwdriver into the hole shown in the illustration while looking into the hole.