Wear protective gloves. Sharp areas on the parts may injure your hands.
71845A
1.REMOVE REAR SEAT UPPER RECLINING COVER RH
Using a screwdriver, detach the 3 claws and remove the cover.
Tape the screwdriver tip before use.
| *1 | Protective Tape |
72525B
2.REMOVE RECLINING ADJUSTER RELEASE HANDLE RH
Remove the 3 screws and handle.
71825B
3.REMOVE REAR SEAT CUSHION MOULDING RH
Using a clip remover, detach the clip.
Using a moulding remover, detach the 3 claws.
Move the moulding in the direction of the arrow to detach the guide and remove the moulding.
71829B
4.REMOVE REAR SEAT REAR CUSHION MOULDING LH
Remove the screw.
Using a moulding remover, detach the 3 claws.
Detach the 2 guides and remove the moulding.
73380C
5.REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY RH
73390A
6.REMOVE REAR SEAT INNER BELT ASSEMBLY
72615A
7.REMOVE REAR SEATBACK LOCK STRIKER COVER RH
Using a clip remover, detach the 3 clips and remove the cover.
8.REMOVE SEAT CUSHION COVER WITH PAD
Detach the hooks and remove the seat cushion cover with pad.
71696
9.REMOVE REAR NO. 2 SEAT PROTECTOR
Remove the 2 protectors from the cushion pad.
71647
10.REMOVE REAR SEAT CUSHION EDGE PROTECTOR
Remove the protector from the cushion spring.
71075S
11.REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER
Remove the hog rings and seat cushion cover from the seat cushion pad.
72572B
12.REMOVE RECLINING ADJUSTER KNOB CAP RH
Using a screwdriver, detach the claw and guide, and then remove the cap.
Tape the screwdriver tip before use.
| *1 | Protective Tape |
72057
13.REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH
Remove the 2 screws.
Disconnect the cable in the order shown in the illustration and remove the lever.
71845C
14.REMOVE REAR SEAT COVER CAP
Using a screwdriver, detach the claw and guide, and then remove the cover cap.
Tape the screwdriver tip before use.
72067A
15.REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY
Remove the 2 screws.
Move the lever in the direction of the arrow to detach the guide and remove the lever.
Detach the cable clamp and disconnect the cable from the lever.
72996A
16.REMOVE REAR SEATBACK COVER
Using a screwdriver, detach the 4 claws and remove the cover.
Tape the screwdriver tip before use.
71880A
17.REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY RH
Using a clip remover, detach the 7 clips and remove the carpet.
71931B
18.REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
Detach the 4 claws and remove the 2 supports.
19.REMOVE SEATBACK COVER WITH PAD
Remove the hog rings and detach the hooks, and then remove the seatback cover with pad.
| *1 | Hook |
| *2 | Hog Ring |
71077S
20.REMOVE SEPARATE TYPE REAR SEATBACK COVER
Remove the hog rings and cover from the seatback pad.
71587A
21.REMOVE REAR SEATBACK EDGE PROTECTOR
Remove the protector from the seatback frame.
71879C
22.REMOVE REAR SEAT INNER RECLINING COVER RH
Remove the 2 screws.
Detach the guide and remove the cover.
71875J
23.REMOVE RECLINING ADJUSTER INSIDE COVER RH
Remove the 2 screws.
Detach the 2 claws and remove the cover.
71876C
24.REMOVE RECLINING ADJUSTER INSIDE COVER RH
Using a clip remover, detach the clip.
Move the cover in the direction of the arrow to detach the 2 claws and remove the cover.
71875E
25.REMOVE RECLINING ADJUSTER INSIDE COVER RH
Detach the claw and guide and remove the cover.
71499D
26.REMOVE REAR SEATBACK SPRING DAMPER
Remove the 2 nuts and damper.
72704A
27.REMOVE REAR SEAT RECLINING CONTROL CABLE
Cut off the 3 cable ties.
Detach the 2 cable clamps and disconnect the cable, and then remove the cable.
72704B
28.REMOVE REAR NO. 2 SEAT RECLINING CONTROL CABLE
Detach the cable clamp and disconnect the cable, and then remove the cable.
71246A
29.REMOVE REAR SEAT CUSHION SET PLATE
Remove the 2 nuts and set plate.
72631
30.REMOVE REAR SEATBACK LOCK PLATE RH
Detach the 2 cable clamps and disconnect the cable.
Remove the nut and lock plate.
71017
31.REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY RH
Using a T40 "TORX" socket wrench, remove the 4 "TORX" bolts and seatback frame.
72995A
32.REMOVE REAR SEAT COVER
Remove the screw and cover.
71461
33.REMOVE REAR SEAT CUSHION SPRING
Detach the 2 hooks and remove the spring.
71015A
34.REMOVE REAR SEAT CUSHION FRAME SUB-ASSEMBLY RH
Remove the 6 nuts and seat cushion frame together with the seat leg plate.
| *1 | Seat Leg Plate |
72173A
35.REMOVE REAR SEAT TRACK ADJUSTING HANDLE RH
Remove the seat cushion side frame.
Slide the slide rail to the rearmost position.
Using a small screwdriver, push down the handle stopper to detach the claw and remove the adjusting handle.
Insert the screwdriver into the hole shown in the illustration while looking into the hole.