Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Slide Walk-in Seat Type RH Side) › 2009.08–2011.10
RM1440E _58 Vehicle Interior _056161 SEAT _0274108 REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Slide Walk-in Seat Type RH Side) A

SEAT  REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Slide Walk-in Seat Type RH Side)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).


PROCEDURE

Hide 72173A 1.INSTALL REAR SEAT TRACK ADJUSTING HANDLE RH

a.
B237931

Install the handle.

HINT:

Make sure the handle is straight when installing it, and check that it is centered.



b.
B241209

Install the seat cushion side frame.


Hide 71015A 2.INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY RH

a.

Install the seat cushion frame and seat leg plate with the 6 nuts.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 71461 3.INSTALL REAR SEAT CUSHION SPRING

a.

Attach the 2 hooks to install the spring.


Hide 72995A 4.INSTALL REAR SEAT COVER

a.

Install the cover with the screw.


Hide 71017 5.INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY RH

a.

Temporarily install the seatback frame with the 4 "TORX" bolts.


b.

Using a T40 "TORX" socket wrench, tighten the 4 "TORX" bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 72631 6.INSTALL REAR SEATBACK LOCK PLATE RH

a.

Install the lock plate with the nut.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Attach the 2 cable clamps and connect the cable.


Hide 71246A 7.INSTALL REAR SEAT CUSHION SET PLATE

a.

Install the set plate with the 2 nuts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 72704B 8.INSTALL REAR NO. 2 SEAT RECLINING CONTROL CABLE

a.

Install the cable.


b.

Attach the cable clamp and connect the cable.


Hide 72704A 9.INSTALL REAR SEAT RECLINING CONTROL CABLE

a.

Install the cable.


b.

Attach the 2 cable clamps and connect the cable.


c.

Install 3 new cable ties.


Hide 71499D 10.INSTALL REAR SEATBACK SPRING DAMPER

a.

Install the damper with the 2 nuts.


Hide 71875E 11.INSTALL RECLINING ADJUSTER INSIDE COVER RH

a.

Attach the claw and guide to install the cover.


Hide 71876C 12.INSTALL RECLINING ADJUSTER INSIDE COVER RH

B241211

a.

Move the cover in the direction of the arrow to attach the 2 claws.


b.

Attach the clip to install the cover.


Hide 71875J 13.INSTALL RECLINING ADJUSTER INSIDE COVER RH

a.

Attach the 2 claws to install the cover.


b.

Install the 2 screws.


Hide 71879C 14.INSTALL REAR SEAT INNER RECLINING COVER RH

a.

Attach the guide and install the cover with the 2 screws.


Hide 71587A 15.INSTALL REAR SEATBACK EDGE PROTECTOR

a.

Install the protector to the seatback frame.


Hide 71077S 16.INSTALL SEPARATE TYPE REAR SEATBACK COVER

B241214E01
2.25,2.422 2.480,2.615 0.230,0.193 10 *1 2.204,2.496 2.038,2.496 2.038,2.496 1.651,3.777 false

a.

Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.

Text in Illustration
*1 Hog Ring Pliers

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




Hide 17.INSTALL SEATBACK COVER WITH PAD

B453513E01
1.958,0.208 2.115,0.208 2.115,0.208 2.292,0.865 true 2.74,0.375 2.104,0.208 2.104,0.208 2.896,0.281 false 2.344,1.375 3.094,1.375 false 5.729,0.667 5.531,0.667 5.531,0.667 5.313,1.792 false 1.781,0.146 2.094,0.344 0.313,0.198 10 false *2 3.167,1.313 3.479,1.51 0.313,0.198 10 false *3 5.781,0.573 6.094,0.771 0.313,0.198 10 false *1

a.

Attach the hooks.

Text in Illustration
*1 Hog Ring Pliers
*2 Hook
*3 Hog Ring


b.

Using hog ring pliers, install the seatback cover with pad with new hog rings.


Hide 71931B 18.INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

a.

Attach the 4 claws to install the 2 supports.


Hide 71880A 19.INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY RH

a.

Attach the 7 clips to install the carpet.


Hide 72996A 20.INSTALL REAR SEATBACK COVER

a.

Attach the 4 claws to install the cover.


Hide 72067A 21.INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY

B165053E07
1.188,2.927 1.427,3.125 0.24,0.198 10 true (1) 1.031,2.177 1.25,2.375 0.219,0.198 10 true (2) 0.719,1.385 0.927,1.542 0.208,0.156 10 false (3)

a.

Connect the cable in the order shown in the illustration to install the lever.


b.

Install the 2 screws.


Hide 71845C 22.INSTALL REAR SEAT COVER CAP

B237755

a.

Attach the guide and claw to install the cap.


Hide 72057 23.INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH

B237946

a.

Attach the cable clamp to connect the cable to the lever.


b.

Move the lever in the direction of the arrow to attach the guide.


c.

Install the lever with the 2 screws.


Hide 72572B 24.INSTALL RECLINING ADJUSTER KNOB CAP RH

a.

Attach the guide and claw to install the cap.


Hide 71075S 25.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER

B237912E02
2.177,2.417 2.01,2.417 2.01,2.417 1.521,3.813 false 2.208,2.323 2.438,2.521 0.229,0.198 10 false *1

a.

Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

Text in Illustration
*1 Hog Ring Pliers

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




Hide 71647 26.INSTALL REAR SEAT CUSHION EDGE PROTECTOR

a.

Install the protector to the cushion spring.


Hide 71696 27.INSTALL REAR NO. 2 SEAT PROTECTOR

a.

Install the 2 protectors to the cushion pad.


Hide 28.INSTALL SEAT CUSHION COVER WITH PAD

B237910

a.

Attach the hooks to install the seat cushion cover with pad.


Hide 72615A 29.INSTALL REAR SEATBACK LOCK STRIKER COVER RH

a.

Attach the 3 clips to install the cover.


Hide 71829B 32.INSTALL REAR SEAT REAR CUSHION MOULDING LH

a.

Attach the guide and 3 claws to install the moulding.


b.

Install the screw.


Hide 71825B 33.INSTALL REAR SEAT CUSHION MOULDING RH

B237717

a.

Move the moulding in the direction of the arrow to attach the guide and install the moulding.


b.

Attach the 3 claws and clip to install the moulding.


Hide 72525B 34.INSTALL RECLINING ADJUSTER RELEASE HANDLE RH

a.

Install the handle with the 3 screws.


Hide 71845A 35.INSTALL REAR SEAT UPPER RECLINING COVER RH

B237787

a.

Attach the 3 claws to install the cover.