Wear protective gloves. Sharp areas on the parts may injure your hands.
A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).
72173A
1.INSTALL REAR SEAT TRACK ADJUSTING HANDLE RH
Install the handle.
Make sure the handle is straight when installing it, and check that it is centered.
Install the seat cushion side frame.
71015A
2.INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY RH
Install the seat cushion frame and seat leg plate with the 6 nuts.
71461
3.INSTALL REAR SEAT CUSHION SPRING
Attach the 2 hooks to install the spring.
72995A
4.INSTALL REAR SEAT COVER
Install the cover with the screw.
71017
5.INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY RH
Temporarily install the seatback frame with the 4 "TORX" bolts.
Using a T40 "TORX" socket wrench, tighten the 4 "TORX" bolts.
72631
6.INSTALL REAR SEATBACK LOCK PLATE RH
Install the lock plate with the nut.
Attach the 2 cable clamps and connect the cable.
71246A
7.INSTALL REAR SEAT CUSHION SET PLATE
Install the set plate with the 2 nuts.
72704B
8.INSTALL REAR NO. 2 SEAT RECLINING CONTROL CABLE
Install the cable.
Attach the cable clamp and connect the cable.
72704A
9.INSTALL REAR SEAT RECLINING CONTROL CABLE
Install the cable.
Attach the 2 cable clamps and connect the cable.
Install 3 new cable ties.
71499D
10.INSTALL REAR SEAT BACK SPRING DAMPER
Install the rear seat back spring damper with the 2 nuts.
71499D
11.INSTALL REAR SEAT BACK SPRING DAMPER
Install the rear seat back spring damper with the 2 nuts.
71875E
12.INSTALL RECLINING ADJUSTER INSIDE COVER RH
Attach the claw and guide to install the cover.
71876C
13.INSTALL RECLINING ADJUSTER INSIDE COVER RH
Move the cover in the direction of the arrow to attach the 2 claws.
Attach the clip to install the cover.
71875J
14.INSTALL RECLINING ADJUSTER INSIDE COVER RH
Attach the 2 claws to install the cover.
Install the 2 screws.
71879C
15.INSTALL REAR SEAT INNER RECLINING COVER RH
Attach the guide and install the cover with the 2 screws.
71587A
16.INSTALL REAR SEATBACK EDGE PROTECTOR
Install the protector to the seatback frame.
71077S
17.INSTALL SEPARATE TYPE REAR SEATBACK COVER
Using hog ring pliers, install the seatback cover to the seatback pad with 8 new hog rings.
| *1 | Hog Ring Pliers |
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
18.INSTALL SEATBACK COVER WITH PAD
Attach the hooks.
| *1 | Hog Ring Pliers |
| *2 | Hook |
| *3 | Hog Ring |
Using hog ring pliers, install the seatback cover with pad with 12 new hog rings.
71931B
19.INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
Attach the 4 claws to install the 2 supports.
71880A
20.INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY RH
Attach the 7 clips to install the carpet.
72996A
21.INSTALL REAR SEATBACK COVER
Attach the 4 claws to install the cover.
72057
22.INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH
Connect the cable in the order shown in the illustration to install the lever.
Install the 2 screws.
72572B
23.INSTALL RECLINING ADJUSTER KNOB CAP RH
Attach the guide and claw to install the cap.
72058
24.INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY
Attach the cable clamp to connect the cable to the lever.
Move the lever in the direction of the arrow to attach the guide.
Install the lever with the 2 screws.
71845C
25.INSTALL REAR SEAT COVER CAP
Attach the guide and claw to install the cap.
71075S
26.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 14 new hog rings.
| *1 | Hog Ring Pliers |
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
71647
27.INSTALL REAR SEAT CUSHION EDGE PROTECTOR
Install the protector to the cushion spring.
71696
28.INSTALL REAR NO. 2 SEAT PROTECTOR
Install the 2 protectors to the cushion pad.
29.INSTALL SEAT CUSHION COVER WITH PAD
Attach the hooks to install the seat cushion cover with pad.
72615A
30.INSTALL REAR SEATBACK LOCK STRIKER COVER RH
Attach the 3 clips to install the cover.
73390A
31.INSTALL REAR SEAT INNER BELT ASSEMBLY
73380C
32.INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY RH
71829B
33.INSTALL REAR SEAT REAR CUSHION MOULDING LH
Attach the 2 guides and 3 claws to install the moulding.
Install the screw.
71825B
34.INSTALL REAR SEAT CUSHION MOULDING RH
Move the moulding in the direction of the arrow to attach the guide and install the moulding.
Attach the 3 claws and clip.
72525B
35.INSTALL RECLINING ADJUSTER RELEASE HANDLE RH
Install the handle with the 3 screws.
71845A
36.INSTALL REAR SEAT UPPER RECLINING COVER RH
Attach the 3 claws to install the cover.