Home › Vehicle Interior › SEAT › SEAT HEATER SWITCH
RM1440E _58 Vehicle Interior _056161 SEAT _0274112 SEAT HEATER SWITCH G

SEAT  SEAT HEATER SWITCH  INSPECTION  


PROCEDURE

Hide 84751 1.INSPECT SEAT HEATER SWITCH LH

B453598E01
2.927,0.854 2.76,0.417 false 3.052,0.854 3.052,0.396 false 3.188,0.854 3.375,0.448 false 2.927,1.125 2.677,1.438 false 3.052,1.115 3.052,1.469 false 3.208,1.104 3.479,1.438 false 1.573,0.833 2.031,1.031 0.458,0.198 10 false 63° 2.271,0.021 2.729,0.219 0.458,0.198 10 false *a 2.688,0.208 2.917,0.396 0.229,0.188 10 false E 2.958,0.208 3.24,0.396 0.281,0.188 10 false SW 3.354,0.229 3.583,0.417 0.229,0.188 10 false ILL- 2.604,1.469 2.833,1.656 0.229,0.188 10 false IG 2.958,1.49 3.26,1.677 0.302,0.188 10 false ILL+ 3.427,1.479 3.656,1.667 0.229,0.188 10 false RV 5.042,0.198 5.385,0.385 0.344,0.188 10 false (kΩ) 4.677,0.542 5.323,0.729 0.646,0.188 10 false 2.7 to 4.1 4.542,0.958 5.323,1.146 0.781,0.188 10 false 0.28 to 0.42 5.198,1.198 5.385,1.375 0.188,0.177 10 false 0 5.302,1.292 5.49,1.469 0.188,0.177 10 false 0 5.604,1.302 5.792,1.479 0.188,0.177 10 false 21 6.313,1.313 6.5,1.49 0.188,0.177 10 false 63 6.708,1.302 6.896,1.479 0.188,0.177 10 false (°) 5.135,1.49 5.479,1.677 0.344,0.188 10 false Off 5.552,1.49 6.135,1.677 0.583,0.188 10 false On (MIN) 6.281,1.49 6.927,1.677 0.646,0.188 10 false On (MAX)

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (SW) - 7 (RV) Switch off 2.7 to 4.1 kΩ
Switch on (Min.)
Switch on (Max.) 0.28 to 0.42 kΩ


HINT:

As the dial is being turned, the resistance changes gradually.


If the result is not as specified, replace the seat heater switch.

Text in Illustration
*a Component without harness connected
(Seat Heater Switch)


b.

Apply battery voltage to the switch connector, and check that the seat heater switch illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 8 (ILL+)
Battery negative (-) → 2 (ILL-)
Illuminates


If the result is not as specified, replace the seat heater switch.


c.

Apply battery voltage to the switch connector, and check that the seat heater switch indicator illuminates.

OK:
Measurement Condition Switch Condition Specified Condition
Battery positive (+) → 9 (IG)
Battery negative (-) → 4 (E)
Switch on Indicator illuminates


If the result is not as specified, replace the seat heater switch.


Hide 84751 2.INSPECT SEAT HEATER SWITCH RH

B453599E01
3.25,0.76 3.01,0.344 false 3.385,0.76 3.385,0.292 false 3.552,0.771 3.698,0.323 false 2.948,1.438 3.25,1.021 false 3.365,1.448 3.365,1.021 false 3.771,1.375 3.563,1.01 false 1.51,0.792 1.969,0.99 0.458,0.198 10 false 63° 2.51,0.052 2.969,0.25 0.458,0.198 10 false *a 2.948,0.177 3.177,0.344 0.229,0.167 10 false E 3.281,0.135 3.552,0.302 0.271,0.167 10 false SW 3.667,0.146 3.948,0.302 0.281,0.156 10 false ILL- 2.813,1.406 3.042,1.573 0.229,0.167 10 false IG 3.26,1.469 3.563,1.656 0.302,0.188 10 false ILL+ 3.729,1.438 3.958,1.604 0.229,0.167 10 false RV 4.979,0.125 5.281,0.323 0.302,0.198 10 false (kΩ) 4.583,0.51 5.229,0.708 0.646,0.198 10 false 2.7 to 4.1 4.448,0.917 5.198,1.104 0.75,0.188 10 false 0.28 to 0.42 5.063,1.135 5.25,1.323 0.188,0.188 10 false 0 5.188,1.25 5.375,1.438 0.188,0.188 10 false 0 5.49,1.26 5.677,1.448 0.188,0.188 10 false 21 6.198,1.271 6.385,1.458 0.188,0.188 10 false 63 6.615,1.26 6.802,1.448 0.188,0.188 10 false (°) 5.115,1.479 5.406,1.688 0.292,0.208 10 false Off 5.479,1.479 6.073,1.677 0.594,0.198 10 false On (MIN) 6.198,1.479 6.844,1.667 0.646,0.188 10 false On (MAX)

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (SW) - 5 (RV) Switch off 2.7 to 4.1 kΩ
Switch on (Min.)
Switch on (Max.) 0.28 to 0.42 kΩ


HINT:

As the dial is being turned, the resistance changes gradually.


If the result is not as specified, replace the seat heater switch.

Text in Illustration
*a Component without harness connected
(Seat Heater Switch)


b.

Apply battery voltage to the switch connector, and check that the seat heater switch illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 6 (ILL+)
Battery negative (-) → 1 (ILL-)
Illuminates


If the result is not as specified, replace the seat heater switch.


c.

Apply battery voltage to the switch connector, and check that the seat heater switch indicator illuminates.

OK:
Measurement Condition Switch Condition Specified Condition
Battery positive (+) → 7 (IG)
Battery negative (-) → 3 (E)
Switch on Indicator illuminates


If the result is not as specified, replace the seat heater switch.