Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) › from 2013.08
RM1440E _58 Vehicle Interior _056161 SEAT _0274116 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Front Power Seat does not Operate with Front Power Seat Switch  


DESCRIPTION

When a signal is input into the front power seat switch LH (position control ECU), the ECU manages the signals received from the front power seat switch LH and operates each motor. When 2 or more signals are input, the motors only operate when the signals are from the slide switch and reclining switch.

WIRING DIAGRAM

B248460E05
0.927,1.656 1.729,1.833 0.802,0.177 10 false from Battery 0.927,0.969 1.729,1.146 0.802,0.177 10 false from Battery 2.51,1.125 3.229,1.292 0.719,0.167 10 false P/SEAT FL 2.625,1.844 3.104,2.01 0.479,0.167 10 false ECU-B 4.896,0.99 5.177,1.135 0.281,0.146 10 false +B1 4.896,1.667 5.292,1.813 0.396,0.146 10 false SYSB 4.896,2.375 5.313,2.531 0.417,0.156 10 false GND1 4.635,0.792 4.74,0.948 0.104,0.156 10 false 7 4.594,1.49 4.781,1.646 0.188,0.156 10 false 12 4.635,2.188 4.74,2.344 0.104,0.156 10 false 2 4.542,2.875 6.313,3.042 1.771,0.167 10 false Front Power Seat Switch LH 4.563,0.99 4.823,1.146 0.26,0.156 10 false b18 4.563,2.375 4.823,2.531 0.26,0.156 10 false b18 4.563,1.677 4.823,1.833 0.26,0.156 10 false b19

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - BATTERY AND BODY GROUND)
a.
U149745E02
1.427,2.781 1.427,3.083 true 1.604,2.021 1.531,2.021 1.531,2.021 1.438,2.5 true 2.177,1.219 2.458,1.219 true 0.135,0.073 0.323,0.26 0.188,0.188 10 false *a 0.51,0.896 0.771,1.052 0.26,0.156 10 false b19 0.5,2.542 0.75,2.698 0.25,0.156 10 false b18 2.51,1.135 2.917,1.292 0.406,0.156 10 false SYSB 1.635,1.948 2.063,2.104 0.427,0.156 10 false GND1 1.344,3.115 1.667,3.271 0.323,0.156 10 false +B1

Disconnect the b18 and b19 front power seat switch LH connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
b18-7 (+B1) - Body ground Always 11 to 14 V
b19-12 (SYSB) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b18-2 (GND1) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Front Power Seat Switch LH)


OK

REPLACE FRONT POWER SEAT SWITCH LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR