Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR(for Front Door)
RM1440E _59 Vehicle Exterior _056166 WINDOW / GLASS _0274165 POWER WINDOW REGULATOR MOTOR(for Front Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Front Door)  INSPECTION  


PROCEDURE

Hide 85720C 1.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

a.
B175750E27
1.74,1.448 1.365,0.458 1.365,0.458 1.26,0.458 true 1.021,3.25 1.604,3.479 false 1.854,3.479 2.385,3.354 false 1.531,3.813 1.115,3.958 false 1.917,3.813 2.375,3.969 false 1.063,0.344 1.26,0.531 0.198,0.188 10 false *a 2.135,2.115 2.365,2.302 0.229,0.188 10 false *b 0.875,3.146 1.24,3.333 0.365,0.188 10 false B 2.427,3.271 2.792,3.458 0.365,0.188 10 false GND 0.885,3.917 1.25,4.104 0.365,0.188 10 false UP 2.406,3.906 2.906,4.094 0.5,0.188 10 false DOWN 2.917,1.167 3.115,1.354 0.198,0.188 10 false *c

Check that the motor gear rotates smoothly as follows.

NOTICE:

Do not apply positive (+) battery voltage to any terminals except terminal 2 (B) to avoid damaging the pulse sensor inside the motor.


OK:
Measurement Condition Specified Condition
1.

Connect the positive (+) battery terminal to terminal 2 (B), and connect the negative (-) battery terminal to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected to the battery, connect the negative (-) battery terminal to terminal 10 (UP).

3.

Disconnect and reconnect the negative (-) battery terminal to terminal 10 (UP) within 1 second.


Motor gear rotates clockwise (Up)
1.

Connect the positive (+) battery terminal to terminal 2 (B), and connect the negative (-) battery terminal to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected to the battery, connect the negative (-) battery terminal to terminal 7 (DOWN).

3.

Disconnect and reconnect the negative (-) battery terminal to terminal 7 (DOWN) within 1 second.


Motor gear rotates counterclockwise (Down)


If the result is not as specified, replace the front power window regulator motor assembly.


CAUTION:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly to the door.


Text in Illustration
*a Motor Gear
*b Clockwise
*c Counterclockwise


Hide 85710D 2.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

a.
B180611E25
1.729,1.479 1.354,0.49 1.354,0.49 1.25,0.49 true 1.031,3.26 1.604,3.479 false 1.865,3.49 2.385,3.354 false 1.531,3.802 1.115,3.948 false 1.917,3.813 2.375,3.969 false 1.042,0.406 1.25,0.594 0.208,0.188 10 false *a 0.323,1.146 0.521,1.333 0.198,0.188 10 false *b 0.896,3.177 1.26,3.365 0.365,0.188 10 false B 2.448,3.271 2.813,3.458 0.365,0.188 10 false GND 0.885,3.896 1.25,4.083 0.365,0.188 10 false UP 2.427,3.906 2.927,4.094 0.5,0.188 10 false DOWN 1.135,2.125 1.354,2.333 0.219,0.208 10 false *c

Check that the motor gear rotates smoothly as follows.

NOTICE:

Do not apply positive (+) battery voltage to any terminals except terminal 2 (B) to avoid damaging the pulse sensor inside the motor.


OK:
Measurement Condition Specified Condition
1.

Connect the positive (+) battery terminal to terminal 2 (B), and connect the negative (-) battery terminal to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected to the battery, connect the negative (-) battery terminal to terminal 10 (UP).

3.

Disconnect and reconnect the negative (-) battery terminal to terminal 10 (UP) within 1 second.


Motor gear rotates counterclockwise (Up)
1.

Connect the positive (+) battery terminal to terminal 2 (B), and connect the negative (-) battery terminal to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected to the battery, connect the negative (-) battery terminal to terminal 7 (DOWN).

3.

Disconnect and reconnect the negative (-) battery terminal to terminal 7 (DOWN) within 1 second.


Motor gear rotates clockwise (Down)


If the result is not as specified, replace the front power window regulator motor assembly.


CAUTION:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly to the door.


Text in Illustration
*a Motor Gear
*b Clockwise
*c Counterclockwise