Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR
RM1440E _59 Vehicle Exterior _056168 DOOR / HATCH _0274179 REAR DOOR N

DOOR / HATCH  REAR DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

B217557E01
0.264,1.555 1.177,1.725 0.913,0.170 10 Centering Bolt 2.12,1.555 3.005,1.725 0.885,0.170 10 Standard Bolt

HINT:
·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.

·

The specified torque for standard bolts is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 1.INSPECT REAR DOOR

a.

Check that the clearance measurements of areas A through H are within each standard range.

B237263E02
5.271,0.448 5.51,0.667 0.24,0.219 10 false A 6.063,2.542 6.302,2.76 0.24,0.219 10 false C 3.531,3.531 3.771,3.75 0.24,0.219 10 false D 1.917,2.406 2.156,2.625 0.24,0.219 10 false E 1.031,2.458 1.271,2.677 0.24,0.219 10 false F 1.875,0.875 2.115,1.094 0.24,0.219 10 false G 4.219,0.417 4.458,0.635 0.24,0.219 10 false H 5.427,1.969 5.667,2.188 0.24,0.219 10 false B

Standard:
Area Measurement Area Measurement
A 3.6 to 6.6 mm (0.142 to 0.260 in.) B 2.7 to 5.7 mm (0.106 to 0.224 in.)
C -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) D 5.35 to 8.35 mm (0.211 to 0.335 in.)
E 3.0 to 6.0 mm (0.118 to 0.236 in.) F -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
G 3.4 to 6.4 mm (0.134 to 0.252 in.) H 3.9 to 6.9 mm (0.154 to 0.272 in.)



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 3.ADJUST REAR DOOR

a.
B237264

Using SST, loosen the hinge bolts on the vehicle body and adjust the door position.

SST
09812-00010  


b.

Tighten the hinge bolts on the vehicle body after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.

Loosen the hinge bolts on the door and adjust the door position.


d.

Tighten the hinge bolts on the door after the adjustment.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


e.
B217848

Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.


f.

Using a brass bar and hammer, hit the striker to adjust its position.


g.

Using a T40 "TORX" socket wrench, tighten the striker mounting screws after the adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 4.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 5.CHECK SRS WARNING LIGHT