Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM1440E _59 Vehicle Exterior _056170 WIPER / WASHER _0274189 WIPER AND WASHER SYSTEM D

WIPER / WASHER  WIPER AND WASHER SYSTEM  SYSTEM DESCRIPTION  


WASHER LINKED OPERATION


a.

When the front wiper washer switch is in the off position and the washer switch is turned on for approximately 0.1 seconds or more, the wipers start on LO at the same time as the washer fluid is sprayed.

Depending on the amount of time for which the washer switch is turned on, the washer-linked operation is performed as follows after the switch is turned off.

E189998E03
3.844,0.396 3.604,0.396 3.604,0.396 3.49,0.948 false 4.458,3.302 4.188,3.302 4.188,3.302 4.104,2.865 false 0.125,0.094 1.896,0.625 1.771,0.531 12 Timing Chart: 4.5,1.177 6.844,1.583 2.344,0.406 10 Approximately 0.1 Seconds 3.906,0.323 6.292,0.75 2.385,0.427 10 Washer Switch on Time 4.521,3.229 6.906,3.625 2.385,0.396 10 Additional Wiper Operation 0.74,1.177 2.208,1.583 1.469,0.406 10 Front Wiper Washer Switch 0.74,2.083 2.271,2.802 1.531,0.719 10 Windshield Wiper Motor Assembly 2.188,1.01 2.625,1.313 0.438,0.302 10 on 2.188,1.406 2.583,1.719 0.396,0.313 10 off 2.188,1.927 2.583,2.229 0.396,0.302 10 on 2.177,2.344 2.51,2.625 0.333,0.281 10 off

Washer Switch on Time Additional Wiper Operation
0.2 sec. or less None
Between 0.2 sec. and 1.5 sec. 1 time
1.5 sec. or more 3 times



INTERMITTENT OPERATION


a.

The system operates the front wipers once in approximately 1.6 to 10.7 seconds when the front wiper switch is turned to the INT position. The intermittent time can be adjusted from 1.6 to 10.7 seconds by using the intermittent time adjust dial.


b.

If the front wiper switch is turned to the INT position, current flows from capacitor C1, which is already charged, through terminals INT1 and INT2 of the front wiper switch to Tr1 (transistor). When Tr1 turns on, current flows from terminal +S of the front wiper switch to terminal +1 of the front wiper switch, then to terminal +1 of the wiper motor, then to the wiper motor and finally to ground, causing the wiper motor to operate. At the same time, current flows from capacitor C1 to terminal INT1 of the front wiper switch, and then to INT2. When the current flow from capacitor C1 ends, Tr1 turns off to turn off the relay contact point and halt the wiper motor.

U181060E02
2.927,2.438 2.927,2.177 false 2.896,6.427 2.896,6.292 false 6.802,5.583 6.802,5.313 false 5.01,2.438 5.01,2.177 false 3.49,2.25 3.49,2.51 false 4.583,2.25 4.583,2.51 false 0.906,1.083 1.708,1.5 0.802,0.417 10 false Front Wiper Switch 4.844,1.417 5.729,1.823 0.885,0.406 10 false Front Washer Switch 1.208,3.125 2.083,3.813 0.875,0.688 10 false Front Wiper Relay Circuit 4.542,4.74 6.24,4.917 1.698,0.177 10 false Windshield Washer Motor 3.917,5.938 5.438,6.115 1.521,0.177 10 false Windshield Wiper Motor 2.198,0.906 2.406,1.073 0.208,0.167 10 false +B 2.094,4.125 2.302,4.292 0.208,0.167 10 false +B 2.573,0.906 2.781,1.073 0.208,0.167 10 false +2 2.458,4.125 2.667,4.292 0.208,0.167 10 false +2 2.938,0.906 3.125,1.063 0.188,0.156 10 false +1 2.823,4.125 3.01,4.281 0.188,0.156 10 false +1 3.302,0.906 3.51,1.063 0.208,0.156 10 false +S 3.094,4.125 3.302,4.281 0.208,0.156 10 false +S 3.604,0.906 3.938,1.073 0.333,0.167 10 false INT1 3.979,0.906 4.333,1.073 0.354,0.167 10 false INT2 4.396,0.906 4.615,1.063 0.219,0.156 10 false B1 1.75,1.094 2.135,1.24 0.385,0.146 10 false MIST 1.76,1.281 2.125,1.458 0.365,0.177 10 false OFF 1.792,1.458 2.063,1.646 0.271,0.188 10 false INT 1.802,1.646 2.052,1.823 0.25,0.177 10 false LO 1.813,1.823 1.969,1.969 0.156,0.146 10 false HI 6.219,1.469 6.5,1.646 0.281,0.177 10 false WF 6.083,4.125 6.365,4.302 0.281,0.177 10 false WF 6.573,1.469 6.813,1.604 0.24,0.135 10 false EW 6.438,4.125 6.677,4.26 0.24,0.135 10 false EW 5.854,1.646 6.167,1.823 0.313,0.177 10 false OFF 5.885,1.833 6.156,2 0.271,0.167 10 false ON 3.698,3.729 3.896,3.875 0.198,0.146 10 false C1 5.844,3.698 6.083,3.875 0.24,0.177 10 false C2 5.531,3.115 5.802,3.26 0.271,0.146 10 false Tr2 4.906,3.333 5.177,3.521 0.271,0.188 10 false Tr1 0.146,0.125 2.792,0.396 2.646,0.271 12 false Front Wiper and Washer System: 2.813,5.646 3.042,5.802 0.229,0.156 10 false LO 2.729,5.99 2.896,6.156 0.167,0.167 10 false HI 1.688,4.635 2.365,4.813 0.677,0.177 10 false WASHER 1.865,5.135 2.167,5.313 0.302,0.177 10 false WIP 0.083,2.115 0.854,2.604 0.771,0.49 10 false Windshield Wiper Switch 0.323,5.51 1.292,5.719 0.969,0.208 10 false Ignition Switch

When the relay contact point turns off, capacitor C1 begins to charge again and Tr1 remains off until charging has been completed. This period corresponds to the intermittent time. When capacitor C1 is fully charged, Tr1 turns on and then the relay contact point turns on, causing the motor to operate again. This cycle is the intermittent operation.

The intermittent time can be adjusted by using the intermittent time adjust dial (variable resistor) to change the charge time of capacitor C1.



WASHER FLUID LEVEL WARNING


a.

When the volume of washer fluid decreases to below a certain level (when the level warning switch is turned on), the combination meter warns the driver through the illumination of the master warning light on the washer warning light.