Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM1440E _59 Vehicle Exterior _056170 WIPER / WASHER _0274190 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 82375B 1.INSTALL WIPER MOTOR WIRE

a.

Attach the claw to install the wiper motor wire.


Hide 85110 2.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.

Using a T30 "TORX" socket, install the wiper motor with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Connect the connector.


c.
E197630E02
1.104,0.917 1.104,1.469 true 1.042,1.49 1.25,1.688 0.208,0.198 10 false *1

Apply MP grease to the crank arm pivot of the wiper crank.

Text in Illustration
*1 Crank Arm Pivot
V100155

MP grease


d.
E197632

Connect the rod to the crank arm pivot of the front wiper crank.


Hide 3.INSTALL WINDSHIELD WIPER MOTOR AND LINK

a.
E198993E01
0.547,0.456 0.748,0.633 0.201,0.177 10 *1 1.959,0.456 2.160,0.633 0.201,0.177 10 *1 0.533,0.564 0.492,0.564 0.492,0.564 0.441,0.981 false 2.134,0.543 2.187,0.543 2.187,0.543 2.483,1.002 false

Attach the grommet as shown in the illustration.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)

Text in Illustration
*1 Grommet

NOTICE:

Be careful not to damage the windshield when installing the windshield wiper motor and link assembly.



b.

Install the windshield wiper motor and link with the 2 bolts.


c.

Connect the connector.


d.

Attach the clamp.


Hide 55781E 4.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.
E198984E02
1.854,1.906 2.031,2.073 0.177,0.167 10 false *1 1.333,0.115 1.51,0.281 0.177,0.167 10 false *2

Attach the 9 guides (B).

Text in Illustration
*1 Guide A
*2 Guide B


b.

Attach the 6 claws and guide (A) as shown in the illustration.


c.

Install the 2 clips to the cowl top ventilator louver sub-assembly.


Hide 55784B 5.INSTALL CENTER NO. 2 COWL TOP VENTILATOR LOUVER

a.

Attach the 2 claws and 2 guides to install the center No. 2 cowl top ventilator louver.


Hide 6.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

a.

Operate the wiper and stop the windshield wiper motor at the automatic stop position.


b.
E112237E10
0.646,2.854 0.958,2.854 0.958,2.854 1.042,3.313 false 2.688,3.698 2.688,3.552 2.688,3.552 1.927,3.5 false 0.5,0.813 0.875,0.813 0.875,0.813 1.365,1.417 true 0.302,0.719 0.479,0.896 0.177,0.177 10 false *1 0.427,2.771 0.615,2.927 0.188,0.156 10 false *2 2.635,3.771 2.813,3.927 0.177,0.156 10 false *3

When reusing the front wiper arm and blade assembly RH:

i.

Clean the wiper arm serrations.

Text in Illustration
*1 Wiper Arm Serration
*2 Wire Brush
*3 Wiper Pivot Serration



c.

When reusing the windshield wiper link assembly:

i.

Clean the wiper pivot serrations with a wire brush.



d.
E198994E01
1.104,0.767 1.337,0.963 0.233,0.196 10 *1 0.9,1.057 0.928,0.861 0.928,0.861 1.082,0.861 false

Install the front wiper arm and blade assembly RH to the position shown in the illustration with the nut.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

Text in Illustration
*1 Ceramic Dot

HINT:
·

Hold the wiper arm by hand while tightening the nut.

·

Raise and lower the wiper arm a few times to confirm that it has settled into the specified position.




Hide 7.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

a.
E112237E10
0.646,2.854 0.958,2.854 0.958,2.854 1.042,3.313 false 2.688,3.698 2.688,3.552 2.688,3.552 1.927,3.5 false 0.5,0.813 0.875,0.813 0.875,0.813 1.365,1.417 true 0.302,0.719 0.479,0.896 0.177,0.177 10 false *1 0.427,2.771 0.615,2.927 0.188,0.156 10 false *2 2.635,3.771 2.813,3.927 0.177,0.156 10 false *3

When reusing the front wiper arm and blade assembly LH:

i.

Clean the wiper arm serrations.

Text in Illustration
*1 Wiper Arm Serration
*2 Wire Brush
*3 Wiper Pivot Serration



b.

When reusing the windshield wiper link assembly:

i.

Clean the wiper pivot serrations with a wire brush.



c.
E198995E01
1.235,0.768 1.433,0.932 0.199,0.164 10 *1 1.208,0.852 1.093,0.852 1.093,0.852 1.057,1.066 false

Install the front wiper arm and blade assembly LH to the position shown in the illustration with the nut.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

Text in Illustration
*1 Ceramic Dot

HINT:
·

Hold the wiper arm by hand while tightening the nut.

·

Raise and lower the wiper arm a few times to confirm that it has settled into the specified position.




d.

Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.


Hide 85292B 8.INSTALL FRONT WIPER ARM HEAD CAP

a.
E201164

Attach the 3 claws to install the front wiper arm head cap.

HINT:

Use the same procedure described for the LH side.



Hide 53867H 9.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

a.

Attach the 5 claws to install the front fender to cowl side seal LH.


Hide 53866J 10.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

HINT:

Use the same procedure described for the LH side.


Hide 53883F 11.INSTALL FRONT FENDER MAIN SEAL LH

a.

Attach the 4 clips and 2 guides.


Hide 53882H 12.INSTALL FRONT FENDER MAIN SEAL RH

HINT:

Use the same procedure described for the LH side.


Hide 53292A 13.INSTALL UPPER RADIATOR SUPPORT SEAL

Hide 14.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).