Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM1440E _59 Vehicle Exterior _056170 WIPER / WASHER _0274190 FRONT WIPER MOTOR G

WIPER / WASHER  FRONT WIPER MOTOR  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 85110 1.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY

a.
E198977E03
0.677,1.469 0.313,1.469 true 2.76,1.479 3.135,1.479 true 0.698,1.406 0.906,1.646 0.208,0.24 10 false *1 0.667,2.76 0.875,3 0.208,0.24 10 false A 1.521,0.635 1.729,0.875 0.208,0.24 10 false B 1.896,0.604 2.104,0.844 0.208,0.24 10 false C 2.656,0.5 2.865,0.74 0.208,0.24 10 false D 2.427,0.26 2.635,0.5 0.208,0.24 10 false E 2.615,1.396 2.823,1.635 0.208,0.24 10 false *1

Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.

Standard:
Area Standard Condition
A 12.5 mm (0.492 in.)
B 23.5 mm (0.925 in.)
C 25.0 mm (0.984 in.)
D 6.5 mm (0.256 in.)
E 46.9 mm (1.85 in.)


Text in Illustration
*1 Moulding Edge


b.

Stop the front wiper motor and link assembly operation.


c.
E198978E02
0.813,3.563 0.531,3.563 false 1.01,3.302 1.094,3.5 1.094,3.5 1.156,3.5 false 1.573,1.5 1.292,1.5 false 1.573,0.938 1.323,0.938 false 1.792,1.219 1.885,1.385 1.885,1.385 1.948,1.385 false 0.458,3.052 0.625,3 0.625,3 0.802,3 false 0.052,0.021 0.281,0.271 0.229,0.25 10 false *A 0.073,2.177 0.323,2.427 0.25,0.25 10 false *B 1.156,0.844 1.344,1 0.188,0.156 10 false *a 1.479,0.969 1.594,1.125 0.115,0.156 10 false a 1.135,1.406 1.323,1.563 0.188,0.156 10 false *b 1.49,1.281 1.677,1.438 0.188,0.156 10 false b 1.979,1.344 2.167,1.5 0.188,0.156 10 false *1 0.292,3 0.479,3.156 0.188,0.156 10 false *a 0.354,3.448 0.542,3.604 0.188,0.156 10 false *b 1.177,3.427 1.365,3.583 0.188,0.156 10 false *1 0.74,3.042 0.854,3.198 0.115,0.156 10 false a 0.74,3.344 0.927,3.5 0.188,0.156 10 false b

Check the automatic stop position.

OK:

The front wipers stop at the positions shown in the illustration.


Standard:
Area Standard Condition
a 10.0 mm (0.398 in.)
b 10.0 mm (0.398 in.)


If the result is not as specified, remove and reinstall the wiper arm and blade assembly and perform the on-vehicle inspection described above to inspect the wiper motor and link assembly again. If the result is not as specified again, inspect the wiper motor and link assembly with it removed from the vehicle body (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSPECTION).

Text in Illustration
*A for LH Side
*B for RH Side
*1 Ceramic Dot
*a Upper Limit
*b Lower Limit