Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH
RM1440E _59 Vehicle Exterior _056170 WIPER / WASHER _0274194 WIPER SWITCH G

WIPER / WASHER  WIPER SWITCH  INSPECTION  


PROCEDURE

Hide 84650 1.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY

a.
U150450E01
0.071,0.027 0.268,0.211 0.198,0.184 10 *a 0.34,1.185 0.488,1.347 0.148,0.163 10 A 0.404,0.737 0.611,0.900 0.208,0.163 10 +2 0.752,0.474 0.959,0.637 0.208,0.163 10 +1 1.289,0.474 1.497,0.637 0.208,0.163 10 +B 1.683,0.474 1.891,0.637 0.208,0.163 10 +S 2.315,1.892 2.627,2.055 0.313,0.163 10 C1R 1.868,1.892 2.180,2.055 0.313,0.163 10 +1R 1.392,1.892 1.659,2.055 0.266,0.163 10 WR 2.119,0.474 2.390,0.637 0.271,0.163 10 WF 2.64,0.474 2.911,0.637 0.271,0.163 10 EW 2.975,1.185 3.135,1.347 0.160,0.163 10 B 2.282,1.075 2.627,0.655 false 2.078,1.079 2.207,0.655 false 1.171,1.08 0.901,0.655 false 1.431,1.076 1.431,0.655 false 1.623,1.086 1.76,0.655 false 0.951,1.107 0.635,0.851 false 2.204,1.387 2.481,1.87 false 2.074,1.413 2.074,1.875 false 1.628,1.421 1.536,1.867 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Front Wiper Switch
Tester Connection Switch Condition Specified Condition
A-1 (+S) - A-3 (+1) Off Below 1 Ω
INT
A-2 (+B) - A-3 (+1) MIST
LO
A-2 (+B) - A-4 (+2) HI

Front Washer Switch:
Tester Connection Switch Condition Specified Condition
B-2 (EW) - B-3 (WF) On Below 1 Ω
Off 10 kΩ or higher

Rear Wiper Switch:
Tester Connection Switch Condition Specified Condition
B-6 (C1R) - B-2 (EW) Off 10 kΩ or higher
B-7 (+1R) - B-2 (EW)
B-6 (C1R) - B-2 (EW) INT Below 1 Ω
B-7 (+1R) - B-2 (EW) HI Below 1 Ω

Rear Washer Switch:
Tester Connection Switch Condition Specified Condition
A-5 (WR) - B-2 (EW) Off 10 kΩ or higher
B-7 (+1R) - B-2 (EW)
A-5 (WR) - B-2 (EW) WASH Below 1 Ω
A-5 (WR) - B-2 (EW) On + WASH Below 1 Ω
B-7 (+1R) - B-2 (EW)


If the result is not as specified, replace the windshield wiper switch assembly.

Text in Illustration
*a Component without harness connected
(Windshield Wiper Switch Assembly)


b.

Check the intermittent operation.

1.

Connect the positive (+) lead of a voltmeter to terminal A-3 (+1) and the negative (-) lead to terminal B-2 (EW).

2.

Connect the positive (+) lead of the battery to terminal A-2 (+B) and the negative (-) lead to terminal B-2 (EW) and A-1 (+S).

3.

Turn the wiper switch to the INT position.

4.

Connect the positive (+) lead of the battery to terminal A-1 (+S) for 5 seconds.

5.

Connect the negative (-) lead of the battery to terminal A-1 (+S). Operate the intermittent wiper relay and check the voltage between terminals A-3 (+1) and B-2 (EW).

OK:

Voltage changes as shown in the illustration.


E056399E54
0.133,0.084 0.337,0.254 0.205,0.170 10 *1 1.734,0.549 2.453,0.700 0.719,0.151 10 10 to 14 V 2.2,1.028 2.474,1.184 0.274,0.156 10 0 V 2.484,1.463 3.642,1.627 1.158,0.164 10 1.6 +/- 1 seconds 2.699,0.205 2.896,0.366 0.197,0.161 10 *2 4.741,0.205 4.933,0.374 0.192,0.170 10 *3 4.625,1.454 5.884,1.610 1.259,0.155 10 10.7 +/- 5 seconds

If the result is not as specified, replace the windshield wiper switch assembly.

Text in Illustration
*1 Voltage between terminals A-3 (+1) and B-2 (EW) *2 FAST: Negative lead of battery connected to terminal A-1 (+S)
*3 SLOW: Negative lead of battery connected to terminal A-1 (+S) - -