Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.12
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.43 mph) for over 20 seconds.

DTC No. DTC Detection Condition Trouble Area
P0617 Conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic).

(a) Vehicle speed is 20 km/h (12.43 mph) or more.

(b) Engine speed is 1000 rpm or more.

(c) STA signal is on.


·

Park/neutral position switch

·

Starter relay (ST) circuit

·

Ignition switch

·

ECM



WIRING DIAGRAM

A227113E08
1.813,1.469 2.219,1.75 0.406,0.281 10 false ST1 1.813,2.219 2.208,2.49 0.396,0.271 10 false ST2 1.333,1.469 1.719,1.75 0.385,0.281 10 false AM1 0.25,2.365 0.667,2.635 0.417,0.271 10 false AM1 1.344,2.219 1.698,2.49 0.354,0.271 10 false AM2 2.167,1.208 2.396,1.49 0.229,0.281 10 false 1 2.167,1.958 2.406,2.26 0.24,0.302 10 false 8 1.156,1.208 1.385,1.479 0.229,0.271 10 false 2 1.167,1.958 1.385,2.208 0.219,0.25 10 false 7 1.26,2.5 1.625,2.76 0.365,0.26 10 false F15 1.25,2.667 2.354,3 1.104,0.333 10 false Ignition Switch 5.844,1.146 6.135,1.5 0.292,0.354 10 false 2 5.125,1.76 5.406,2.031 0.281,0.271 10 false 4 4.896,2.604 5.167,2.906 0.271,0.302 10 false 5 5.76,1.344 6.188,1.667 0.427,0.323 10 false B37 6.094,1.333 6.583,1.594 0.49,0.26 10 false NSW 5.063,2.594 5.479,2.813 0.417,0.219 10 false B51 5.063,2.781 5.844,3.594 0.781,0.813 10 false Park/Neutral Position Switch Assembly 0.927,3.208 1.24,3.479 0.313,0.271 10 false ST 3.688,4.49 4.115,4.844 0.427,0.354 10 false ST 1.156,4.25 1.438,4.521 0.281,0.271 10 false 1 1.969,4.135 2.219,4.417 0.25,0.281 10 false 1 1.125,4.458 1.5,4.76 0.375,0.302 10 false C3 2.198,4.177 2.542,4.5 0.344,0.323 10 false C6 1.052,5.823 1.708,6.198 0.656,0.375 10 false Battery 1.573,5.271 2.875,5.708 1.302,0.438 10 false Starter Assembly 3.323,3.635 3.604,3.896 0.281,0.26 10 false 3 4.125,3.635 4.396,3.927 0.271,0.292 10 false 5 3.333,4.063 3.604,4.333 0.271,0.271 10 false 2 4.125,4.063 4.354,4.323 0.229,0.26 10 false 1 5.802,3.979 6.063,4.229 0.26,0.25 10 false 10 5.76,4.177 6.198,4.5 0.438,0.323 10 false F50 6.094,4.177 6.51,4.469 0.417,0.292 10 false STA 6.292,4.635 6.792,5.01 0.5,0.375 10 false ECM 0.271,3.823 0.656,4.052 0.385,0.229 10 false ALT

CAUTION / NOTICE / HINT

HINT:
·

The following troubleshooting flowchart is based on the premise that the engine can be cranked normally.

If the engine does not crank, proceed to Problem Symptoms Table (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


e.

Read the value.

OK:
Ignition Switch Position Starter Signal
ON OFF
START ON




OK

NG

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

OK

3.REPAIR OR REPLACE HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - STA TERMINAL OF ECM)

NG

3.REPAIR OR REPLACE HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - STA TERMINAL OF ECM)

NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.



e.

Drive the vehicle at more than 20 km/h (12.43 mph) for over 20 seconds.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Code.


g.

Read DTCs.

Result
Display (DTC Output) Proceed to
P0617 A
No DTC B



A

B

END