SFI SYSTEM > DETAILS



FUNCTION OF MAIN COMPONENTS
  1. The main components of the engine control system are as follows:

    Component
    Outline
    Quantity
    Function
    ECM
    32-bit CPU
    1
    The ECM optimally controls the SFI, ESA and ISC to suit the operating conditions of the engine in accordance with the signals provided by the sensors.
    Mass Air Flow Meter
    Hot-wire Type
    1
    This sensor has a built-in hot-wire to directly detect the intake air mass.
    Intake Air Temperature Sensor
    Thermistor Type
    1
    This sensor detects the intake air temperature by means of an internal thermistor.
    Engine Coolant Temperature Sensor
    Thermistor Type
    1
    This sensor detects the engine coolant temperature by means of an internal thermistor
    Crankshaft Position Sensor [Rotor Teeth]
    Pick-up Coil Type [36 - 2]
    1
    This sensor detects the engine speed and performs cylinder identification.
    Camshaft Position Sensor for Intake [Rotor Teeth]
    Magnetic Resistance Element (MRE) Type [3]
    2 (1 each bank)
    This sensor performs cylinder identification
    Camshaft Position Sensor for Exhaust [Rotor Teeth]
    Magnetic Resistance Element (MRE) Type [3]
    2 (1 each bank)
    This sensor performs cylinder identification
    Accelerator Pedal Position Sensor
    Linear (Non-contact) Type
    1
    This sensor detects the amount of pedal effort applied to the accelerator pedal.
    Throttle Position Sensor
    Linear (Non-contact) Type
    1
    This sensor detects the throttle valve opening angle.
    Knock Control Sensor (Bank 1 and Bank 2)
    Built-in Piezoelectric Type (Non-resonant Type/ Flat Type)
    2 (1 each bank)
    This sensor detects an occurrence of engine knocking indirectly from the vibration of the cylinder block caused by the occurrence of engine knocking.
    Air Fuel Ratio Sensor (Bank 1, Sensor 1) (Bank 2, Sensor 1)
    Heated Type (Planar Type)
    2 (1 each bank)
    As with the oxygen sensor, this sensor detects the oxygen concentration in the exhaust emission. However, it detects the oxygen concentration in the exhaust emission linearly.
    Heated Oxygen Sensor (Bank 1, Sensor 2) (Bank 2, Sensor 2)
    Heated Type (Cup Type)
    2 (1 each bank)
    This sensor detects the oxygen concentration in the exhaust emission by measuring the electromotive force which is generated in the sensor itself.
    Fuel Injector Assembly
    12-hole Type
    6
    The injector is an electromagnetically-operated nozzle which injects fuel in accordance with signals from the ECM.
    Emission Control Valve Set
    Solenoid Valve
    2
    To ensure the proper warm-up performance of the Three-Way Catalytic converters (TWCs) after starting a cold engine, an air injection system is used.
    Air Injection Control Driver
    Solenoid Valve
    1
    Air Pump Assembly
    DC Type Pump Motor
    1


SYSTEM CONTROL
  1. The engine control system of the 1GR-FE engine has the following features. The ECM that controls this system is made by DENSO.

    System
    Outline
    Sequential Multiport Fuel Injection (SFI)
    An L-type SFI system directly detects the intake air volume with a hot-wire type mass air flow meter.
    Electronic Spark Advance (ESA)
    1. Ignition timing is determined by the ECM based on signals from various sensors. The ECM corrects ignition timing in response to engine knocking.
    2. This system selects the optimal ignition timing in accordance with the signals received from the sensors and sends (IGT) ignition signals to the igniters.
    Electronic Throttle Control System-intelligent (ETCS-i)
    Optimally controls the opening angle of the throttle valve in accordance with the accelerator pedal input and the engine and vehicle conditions.
    Dual Variable Valve Timing-intelligent (Dual VVT-i)
    Controls the intake and exhaust camshaft to an optimal valve timing in accordance with engine operating conditions.
    Fuel Pump Control
    Fuel pump operation is controlled by signals from the ECM. The fuel pump is stopped when the SRS airbags deploy.
    Air Injection Control
    This system uses an electric air pump for pumping air to the cylinder head. This ensures the proper warm-up performance of the TWC during cooled down engine state.
    Air Conditioning Cut-off Control
    By turning the air conditioning compressor ON or OFF in accordance with the engine conditions, drivability is maintained.
    Starter Control* (Cranking Hold Function)
    Once the engine switch is pushed, this control operates the starter until the engine starts.
    Air Fuel Ratio Sensor and Heated Oxygen Sensor Heater Control
    Maintains the temperature of the air fuel ratio sensors or heated oxygen sensors at an appropriate level to increase the ability of the sensor to accurately detect oxygen concentration.
    Engine Immobilizer
    Prohibits fuel delivery and ignition if an attempt is made to start the engine with an invalid key.
    Diagnosis
    When the ECM detects a malfunction, the ECM records the malfunction and information that relates to the fault.
    Fail-safe
    When the ECM detects a malfunction, the ECM stops or controls the engine according to the data already stored in the memory.

    1. *: Models with Smart Key System


FUNCTION


  1. Dual VVT-i System



    1. The Dual Variable Valve Timing-intelligent (Dual VVT-i) system is designed to control the intake and exhaust camshaft within a range of 40° and 35° respectively (of Crankshaft Angle) to provide valve timing that is optimally suited to the engine operating conditions. This improves torque in all the speed ranges as well as increasing fuel economy, and reducing exhaust emissions.


      W102061E01


      Text in Illustration 
      *1
      Camshaft Timing Oil Control Valve Assembly (RH, Exhaust)
      *2
      Camshaft Timing Oil Control Valve Assembly (Intake RH)
      *3
      Camshaft Position Sensor (Exhaust RH)
      *4
      Engine Coolant Temperature Sensor
      *5
      Camshaft Timing Oil Control Valve Assembly (Intake LH)
      *6
      Camshaft Position Sensor (Exhaust LH)
      *7
      Camshaft Timing Oil Control Valve Assembly (Exhaust LH)
      *8
      Camshaft Position Sensor (Intake LH)
      *9
      Crankshaft Position Sensor
      *10
      Camshaft Position Sensor (Intake RH)
      *11
      ECM
      *12
      1. Mass Air Flow Meter
      2. Throttle Position Sensor

    2. The VVT-i system delivers excellent benefits in the different operating conditions as shown in the table below.

      Operation State
      Objective
      Effect
      During Idling
      W102062E01
      Eliminating overlap reduces blow back to the intake side.
      1. Stabilized idling rpm
      2. Better fuel economy
      At Light Load
      W102063E01
      Eliminating overlap reduces blow back to the intake side.
      Engine stability is ensured
      At Medium Load
      W102064E01
      Increasing overlap increases internal EGR, reducing pumping losses.
      1. Better fuel economy
      2. Improved emission control
      In Low to Medium Speed Range with Heavy Load
      W102065E01
      Advancing the intake valve closing timing improves volumetric efficiency.
      Improved torque in low to medium speed range
      In High Speed Range with Heavy Load
      W102066E01
      Retarding the intake valve closing timing improves volumetric efficiency.
      Improved output
      At Low Temperatures
      W102062E01
      Eliminating overlap to reduce blow back to the intake side stabilizes the idling speed at fast idle.
      1. Stabilized fast idle rpm
      2. Better fuel economy
      1. Starting the Engine
      2. Stopping the Engine
      W102062E01
      Eliminating overlap minimize blow back to the intake side.
      Improved startability



  2. Electronic Throttle Control System-intelligent (ETCS-i)

    1. The ETCS-i is used, providing excellent throttle control in all operating ranges. The accelerator cable has been discontinued, and an accelerator pedal position sensor has been provided on the accelerator pedal.

    2. In the conventional throttle body, the throttle valve opening is determined invariably by the amount of accelerator pedal effort. In contrast, the ETCS-i uses the ECM to calculate the optimal throttle valve opening that is appropriate for the respective driving condition and uses a throttle control motor to control the opening.

    3. The ETCS-i controls the Idle Speed Control (ISC) system, Traction Control (TRC) and Vehicle Stability Control (VSC) system.



    4. In case of an abnormal condition, this system switches to the limp mode.


      W102733E03

  3. Fuel Pump Control

    1. The fuel pump is controlled by the ECM, using the fuel pump control ECU. The fuel pump control has a fuel cut control. Fuel cut control stops the fuel pump when any of the SRS airbags have deployed.

  4. Cranking Hold Function (Models with Smart Key System)

    1. Once the engine switch is pressed, this function operates the starter until the engine starts, provided that the brake pedal is depressed and the shift lever is in P or N. This prevents application of the starter for an inadequate length of time. It also prevents the engine from being cranked after it has started. For details, Click here.


CONSTRUCTION


  1. Air Fuel Ratio Sensor and Heated Oxygen Sensor

    1. A planar type air fuel ratio sensor and a cup type heated oxygen sensor are used. The basic construction of the heated oxygen sensor and the air fuel ratio sensor is the same. However, they are divided into the cup type and the planar type, according to the different types of heater construction used.

    2. The planar type air fuel ratio sensor uses alumina, which excels in heat conductivity and electrical insulation, to integrate a sensor element with a heater, thus improving the warm-up performance of the sensor.



    3. The cup type heated oxygen sensor contains a sensor element that surrounds a heater.


      W103726E02


      Text in Illustration 
      *A
      Air Fuel Ratio Sensor (Planar Type)
      *B
      Heated Oxygen Sensor (Cup Type)
      *1
      Diffusion Resistance Layer
      *2
      Atmosphere
      *3
      Heater
      *4
      Platinum Electrode
      *5
      Alumina
      *6
      Sensor Element (Zirconia)



    4. As illustrated below, the conventional heated oxygen sensor is characterized by a sudden change in its output voltage at the threshold of the stoichiometric air-fuel ratio (14.7:1). In contrast, the air-fuel ratio sensor data is approximately proportionate to the existing air-fuel ratio. The air-fuel ratio sensor converts the oxygen density to current and sends it to the ECM. As a result, the detection precision of the air-fuel ratio has been improved. The air-fuel ratio sensor data can be viewed using Techstream.


      W100042E02



  2. Mass Air Flow Meter

    1. The mass air flow meter, which is a slot-in type, allows a portion of the intake air to flow through the detection area. By directly measuring the mass and the flow rate of the intake air, the detection precision is improved and the intake air resistance is reduced.



    2. This mass air flow meter has a built-in intake air temperature sensor.


      W102067E02


      Text in Illustration 
      *1
      Platinum Hot-wire Element
      *2
      Temperature Sensing Element
      *3
      Intake Air Temperature Sensor
      -
      -
      *a
      A - A Cross Section
      -
      -
      V100135
      Air Flow
      -
      -



  3. Crankshaft Position Sensor



    1. The timing rotor of the crankshaft consists of 34 teeth with 2 teeth missing. The crankshaft position sensor outputs the crankshaft rotation signals every 10°, and the change of the signal due to the missing teeth is used to determine top-dead-center.


      W102705E01



  4. Camshaft Position Sensor



    1. Magnetic Resistance Element (MRE) type camshaft position sensors (intake and exhaust) are used. To detect each camshaft (intake) position, a timing rotor that is secured to the camshaft (intake) in front of the camshaft timing gear assembly is used to generate 6 (3 Hi Output, 3 Lo Output) pulses for every 2 revolutions of the crankshaft. The timing rotor for each camshaft (exhaust) is part of the respective camshaft.


      W102073E01


      Text in Illustration 
      *1
      Camshaft Position Sensor (Exhaust, RH)
      *2
      Timing Rotor
      *3
      Camshaft Position Sensor (Intake, RH)
      -
      -

      W102098E01



    2. An MRE type camshaft position sensor consists of an MRE, a magnet and a sensor. The direction of the magnetic field changes due to the profile (protruding and non-protruding portions) of the timing rotor, which passes by the sensor. As a result, the resistance of the MRE changes, and the output voltage to the ECM changes to Hi or Lo. The ECM detects the camshaft position based on this output voltage.


      W100046E03



  5. Knock Control Sensor (Flat Type)

    1. In a conventional knock control sensor (resonant type), a vibration plate is built into the sensor. This plate has the same resonance point as the knocking* frequency of the engine block. This sensor can only detect vibration in this frequency band.
      *: The term "Knock" or "Knocking" is used in this case to describe either preignition or detonation of the air fuel mixture in the combustion chamber. This preignition or detonation refers to the air fuel mixture being ignited earlier than is advantageous. This use of "Knock" or "Knocking" is not primarily used to refer to a loud mechanical noise that may be produced by an engine.
      A flat type knock control sensor (non-resonant type) has the ability to detect vibration in a wider frequency band (from about 5 kHz to 15 kHz). It has the following features:

      1. A flat type knock control sensor is installed to an engine by placing it over the stud bolt installed on the cylinder block sub-assembly. For this reason, a hole for the stud bolt exists in the center of the sensor.
      2. In the sensor, a steel weight is located in the upper portion. An insulator is located between the weight and a piezoelectric element.
      3. An open/short circuit detection resistor is integrated in the sensor.



    2. The engine knocking frequency will vary slightly depending on the engine speed. The flat type knock control sensor can detect vibration even when the engine knocking frequency changes. Due to the use of the flat type knock control sensor, the vibration detection ability is increased compared to a conventional type knock control sensor, and more precise ignition timing control is possible.


      W100047E01



    3. An open or short circuit detection resistor is integrated in the sensor. When the ignition is ON, the open or short circuit detection resistor in the knock control sensor and the resistor in the ECM keep the voltage at terminal KNK1 constant. An Integrated Circuit (IC) in the ECM constantly monitors the voltage of terminal KNK1. If an open or short circuit occurs between the knock control sensor and the ECM, the voltage of terminal KNK1 will change and the ECM will detect this and store a Diagnostic Trouble Code (DTC).


      W102097E01


      Text in Illustration 
      *A
      Flat Type (Non-Resonant Type)
      *B
      Conventional Type (Resonant Type)
      *1
      Steel Weight
      *2
      Piezoelectric Element
      *3
      Insulator
      *4
      Open Circuit Detection Resistor
      *5
      Vibration Plate
      -
      -

      W102099E02



    4. Vibrations caused by knocking are transmitted to the steel weight. The inertia of this weight applies pressure to the piezoelectric element. This action generates electromotive force.


      W100049E01


      Text in Illustration 
      *1
      Steel Weight
      *2
      Inertia
      *3
      Piezoelectric Element
      -
      -



    5. These knock control sensors are mounted in the specific directions and angles as illustrated. To prevent the right and left bank connectors from being interchanged, make sure to install each sensor in its prescribed direction.


      W102068E01


      Text in Illustration 
      *1
      Knock Control Sensor (KNK1)
      *2
      Knock Control Sensor (KNK2)
      V100135
      Engine Front
      V100136
      Knock Control Sensor Mounting Direction

  6. Throttle Position Sensor

    1. This non-contact type throttle position sensor uses a Hall IC, which is mounted on the throttle body.

      1. The Hall IC is surrounded by a magnetic yoke. The Hall IC converts the changes that occur in the magnetic flux into electrical signals, and outputs them in the form of throttle valve position signals to the ECM.

      2. The Hall IC contains circuits for the main and sub signals. It converts the throttle valve opening angle into electric signals that have differing characteristics, and outputs them to the ECM.


        W102100E01


        Text in Illustration 
        *1
        Magnet
        *2
        Hall IC
        *a
        Throttle Position Sensor
        -
        -


        W102101E01

      HINT:
      The inspection method differs from a contact type throttle position sensor because a non-contact type throttle position sensor uses a Hall IC. For details, refer to the 2013 4RUNNER Repair Manual (Pub.No. RM22R0U).

  7. Accelerator Pedal Position Sensor

    1. This non-contact type accelerator pedal position sensor uses a Hall IC, which is mounted on the accelerator pedal arm.

      1. A magnetic yoke is mounted at the base of the accelerator pedal arm. This yoke rotates around the Hall IC in accordance with the amount of effort that is applied to the accelerator pedal. The Hall IC converts the changes in the magnetic flux that occur into electrical signals, and outputs them in the form of accelerator pedal position signals to the ECM.

      2. The Hall IC contains two circuits, one for the main signal, and one for the sub signal. It converts the accelerator pedal position (angle) into electric signals that have differing characteristics and outputs them to the ECM.


        W110570E01


        Text in Illustration 
        *1
        Hall IC
        *2
        Magnetic Yoke
        *3
        Accelerator Pedal Arm
        -
        -


        W102103E02

      HINT:
      The inspection method differs from a contact type accelerator pedal position sensor because a non-contact type accelerator pedal position sensor uses a Hall IC. For details, refer to the 2013 4RUNNER Repair Manual (Pub.No. RM22R0U).



  8. Camshaft Timing Oil Control Valve Assembly



    1. This camshaft timing oil control valve assembly controls the spool valve using duty-cycle control from the ECM. This allows hydraulic pressure to be applied to the camshaft timing gear assembly or camshaft timing exhaust gear assembly advance or retard side. When the engine is stopped, the camshaft timing oil control valve assembly (intake) will move to the retard position, and the camshaft timing oil control valve assembly (exhaust) will move to the advance position.


      W102069E01


      Text in Illustration (Intake Side) 
      *1
      Spool Valve
      *2
      Sleeve
      *3
      Spring
      *4
      Plunger
      *5
      Coil
      -
      -
      *a
      To Camshaft Timing Gear Assembly (Advance Side)
      *b
      To Camshaft Timing Gear Assembly (Retard Side)
      *c
      Drain
      *d
      Oil Pressure

      W102093E01


      Text in Illustration (Exhaust Side) 
      *1
      Spool Valve
      *2
      Sleeve
      *3
      Spring
      *4
      Plunger
      *5
      Coil
      -
      -
      *a
      To Camshaft Timing Gear Assembly (Retard Side)
      *b
      To Camshaft Timing Gear Assembly (Advance Side)
      *c
      Drain
      *d
      Oil Pressure



  9. Ignition Coil Assembly



    1. The Direct Ignition System (DIS) provides 6 ignition coil assemblies, one for each cylinder. The spark plug caps, which provide contact to the spark plugs, are integrated with the ignition coil assembly. Also, an igniter is enclosed to simplify the system.


      W102070E01


      Text in Illustration (Ignition Coil Assembly Cross Section) 
      *1
      Igniter
      *2
      Iron Core
      *3
      Secondary Coil
      *4
      Primary Coil
      *5
      Plug Cap
      -
      -



  10. Spark Plug

    1. Long-reach type spark plugs are used. This type of spark plug allows the area of the cylinder head sub-assembly that receives the spark plugs to be made thick. Thus, the water jacket can be extended near the combustion chamber, which contributes to cooling performance.



    2. Iridium-tipped spark plugs are used to achieve a 120000 mile (192000 km) maintenance interval. By making the center electrode of iridium, it is possible to achieve superior ignition performance and durability when compared to platinum-tipped spark plugs.


      W102071E01


      Text in Illustration 
      *A
      Long-Reach Type
      *B
      Conventional Type
      *1
      Water Jacket
      *2
      Iridium Tip
      *3
      Platinum Tip
      -
      -


OPERATION


  1. Dual VVT-i System



    1. Based on engine speed, intake air volume, throttle position and engine coolant temperature, the ECM calculates optimal valve timing for all driving conditions. The ECM also controls the camshaft timing oil control valve assemblies. In addition, the ECM uses signals from the camshaft position sensors and the crankshaft position sensor to detect the actual valve timing, thus providing feedback control to achieve the target valve timing.


      W100056E01



    2. When the camshaft timing oil control valve assembly is positioned as illustrated below by the advance signals from the ECM, the resultant oil pressure is applied to the timing advance side vane chamber to rotate the camshaft in the timing advance direction.


      W102111E01


      Text in Illustration (Advance Side Operation Intake Side) 
      *1
      Vane
      *2
      ECM
      V100135
      Oil Flow
      V100136
      Rotation Direction

      W102112E01


      Text in Illustration (Advance Side Operation Exhaust Side) 
      *1
      Vane
      *2
      ECM
      V100135
      Oil Flow
      V100136
      Rotation Direction



    3. When the camshaft timing oil control valve assembly is positioned as illustrated below by the retard signals from the ECM, the resultant oil pressure is applied to the timing retard side vane chamber to rotate the camshaft in the timing retard direction.


      W102113E01


      Text in Illustration (Retard Side Operation Intake Side) 
      *1
      Vane
      *2
      ECM
      V100135
      Oil Flow
      V100136
      Rotation Direction

      W102114E01


      Text in Illustration (Retard Side Operation Exhaust Side) 
      *1
      Vane
      *2
      ECM
      V100135
      Oil Flow
      V100136
      Rotation Direction

    4. After reaching the target timing, the engine valve timing is maintained by keeping the camshaft timing oil control valve assembly in the neutral position unless the engine operating conditions change.
      This maintains the engine valve timing at the desired target position by preventing the engine oil from running out of the camshaft timing oil control valve assembly.



  2. Fuel Pump Control

    1. By adopting a linear type fuel pump control ECU with PWM (Pulse Width Modulation) control, the size and weight have been reduced and fuel economy has been improved due to lower electricity consumption.

    2. The fuel pump control ECU receives three-stage drive request signals (duty signals) from the ECM and drives the fuel pump.

    3. The fuel pump control is used to stop the fuel pump when the airbags deploy in a front or side collision.

    4. In this system, when the airbag deployment signal from the center airbag sensor assembly is detected by the ECM, the ECM turns off the circuit opening relay.



    5. After the fuel cut control has been activated, turning the power source from off to ON cancels the fuel cut control, and the engine can be restarted.


      W109864E01