Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > DIAGNOSIS SYSTEM

for Preparation Click here



DESCRIPTION
  1. When troubleshooting OBD (On-Board Diagnostics) II vehicles, the Techstream (complying with SAE J1987) must be connected to the DLC3 (Data Link Connector 3) of the vehicle. Various data in the ECM (Engine Control Module) can then be read.

  1. FI00534E01
    OBD II regulations require that the vehicle's on-board computer illuminate the MIL (Malfunction Indicator Lamp) on the instrument panel when the computer detects a malfunction in:
    1. The emission control system components.
    2. The powertrain control components which affect vehicle emissions.
    3. The computer itself.
  1. In addition, the applicable DTCs (Diagnostic Trouble Codes) prescribed by SAE J2012 are stored in the ECM memory. If the malfunction does not recur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain stored in the ECM memory.
  1. To check DTCs, connect the Techstream to the DLC3. The Techstream displays DTCs, freeze frame data and a variety of engine data. The DTCs and freeze frame data can be cleared with the Techstream (Click here).
    In order to enhance OBD function on vehicles and develop the Off-Board diagnosis system, CAN (Controller Area Network) communication is used in this system. It minimizes the gap between technician skills and vehicle technology. CAN is a network, which uses a pair of data transmission lines, spanning multiple computers and sensors. It allows high speed communication between the systems and simplifies the wire harness connection.

NORMAL MODE AND CHECK MODE
The diagnosis system operates in normal mode during normal vehicle use. In normal mode, 2 trip detection logic is used to ensure accurate detection of malfunctions. Check mode is also available as an option for technicians. In check mode, 1 trip detection logic is used to increase the system's ability to detect malfunctions, including intermittent problems, when simulating malfunction symptoms (Techstream only) (Click here).

2 TRIP DETECTION LOGIC
When a malfunction is first detected, the DTC is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected during the next subsequent driving cycle, the MIL is illuminated (2nd trip).

FREEZE FRAME DATA
Freeze frame data records the engine conditions (fuel system information, calculated engine load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

DLC3 (Data Link Connector 3)
  1. Check the DLC3 (Click here).


BATTERY VOLTAGE
If the voltage is below 11 V, replace or recharge the battery before proceeding.

Standard voltage:
11 to 14 V


MIL (Malfunction Indicator Lamp)
  1. The MIL is illuminated when the ignition switch is first turned to ON (the engine is not running).

  2. The MIL should turn off when the engine starts. If the MIL remains illuminated, the diagnosis system has detected a malfunction or abnormality in the system.

    HINT:
    If the MIL is not illuminated when the ignition switch is first turned ON, check the MIL circuit (Click here).


ALL READINESS

HINT:
  1. With All Readiness, you can check whether or not the DTC judgment has been completed by using the Techstream.
  2. Check All Readiness after simulating malfunction symptoms or for validation after finishing repairs.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Clear the DTCs (Click here).

  5. Perform the DTC judgment driving pattern to run the DTC judgment.

  6. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  7. Input the DTCs to be confirmed.

  8. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit