DTC P0010 Camshaft Position "A" Actuator Circuit (Bank 1) |
DTC P0020 Camshaft Position "A" Actuator Circuit (Bank 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0010 | Open or short in the camshaft timing oil control valve for the intake camshaft (bank 1) circuit (1 trip detection logic). |
|
| P0020 | Open or short in the camshaft timing oil control valve for the intake camshaft (bank 2) circuit (1 trip detection logic). |
|
| Related DTCs | P0010: Camshaft timing oil control valve range check (bank 1) P0020: Camshaft timing oil control valve range check (bank 2) |
| Required Sensors/Components (Main) | Camshaft timing oil control valve |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 1 second |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| All of following conditions met | - |
| Starter | OFF |
| Ignition switch | ON |
| Time after ignition switch off to ON | 0.5 seconds or more |
| One of following conditions met | - |
| A. All of following conditions met | - |
| Battery voltage | 11 to 13 V |
| Target duty ratio | Less than 70% |
| Output signal duty ratio | 100% |
| B. All of following conditions met | - |
| Battery voltage | 13 V or higher |
| Target duty ratio | Less than 80% |
| Output signal duty ratio | 100% |
| C. Both of following conditions met | - |
| Current cut status | Not cut |
| Output signal duty ratio | 3% or less |
| Camshaft timing oil control valve duty ratio | 3 to 100% |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CHECK DTC |
Clear the DTCs after recording the freeze frame data and DTCs.
Turn the ignition switch off.
Allow the engine to idle and check for DTCs.
Check that P0010 or P0020 is output.
|
| ||||
| OK | |
| 2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
Inspect the camshaft timing oil control valve assembly (for Intake Side of Bank 1, 2) .
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM) |
Disconnect the camshaft timing oil control valve assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B16-1 - B37-19 (OC1+) | Always | Below 1 Ω |
| B19-1 - B36-19 (OC2+) | Always | Below 1 Ω |
| B16-2 - B37-20 (OC1-) | Always | Below 1 Ω |
| B19-2 - B36-20 (OC2-) | Always | Below 1 Ω |
| B16-1 or B37-19 (OC1+) - Body ground | Always | 10 kΩ or higher |
| B19-1 or B36-19 (OC2+) - Body ground | Always | 10 kΩ or higher |
| B16-2 or B37-20 (OC1-) - Body ground | Always | 10 kΩ or higher |
| B19-2 or B36-20 (OC2-) - Body ground | Always | 10 kΩ or higher |
Reconnect the camshaft timing oil control valve assembly connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||