Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM

WIPER AND WASHER SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B235899E01

  1. Remove the main body ECU (multiplex network body ECU) (Click here).

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A-30 (BECU) - Body ground
    -
    Battery power supply
    Always
    11 to 14 V
    A-31 (ALTB) - Body ground
    -
    Battery power supply
    Always
    11 to 14 V
    A-32 (IG) - Body ground
    -
    Ignition switch power supply
    Ignition switch ON
    11 to 14 V
    A-32 (IG) - Body ground
    -
    Ignition switch power supply
    Ignition switch off
    Below 1 V
    A-29 (ACC) - Body ground
    -
    ACC power supply
    Ignition switch ACC
    11 to 14 V
    A-29 (ACC) - Body ground
    -
    ACC power supply
    Ignition switch off
    Below 1 V
    A-11 (GND1) - Body ground
    -
    Ground
    Always
    Below 1 Ω
    F10-3 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Install the main body ECU (multiplex network body ECU).

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F10-8 (RWSW) - Body ground
    P - Body ground
    Rear washer switch input
    Ignition switch ON, rear washer switch on
    Below 1 V
    F10-8 (RWSW) - Body ground
    P - Body ground
    Rear washer switch input
    Ignition switch ON, rear washer switch off
    Pulse generation (See waveform 1 or 2)
    F10-17 (RWLS) - Body ground
    R- Body ground
    Rear wiper switch input
    Ignition switch ON, rear wiper switch INT
    Below 1 V
    F10-17 (RWLS) - Body ground
    R - Body ground
    Rear wiper switch input
    Ignition switch ON, rear wiper switch off
    Pulse generation (See waveform 1 or 2)
    F9-1 (RWC1) - Body ground
    B - Body ground
    Rear wiper switch input
    Ignition switch ON, rear wiper switch LO
    Below 1 V
    F9-1 (RWC1) - Body ground
    B- Body ground
    Rear wiper switch input
    Ignition switch ON, rear wiper switch off
    Pulse generation (See waveform 1 or 2)
    F8-2 (BW) - Body ground
    B - Body ground
    Rear washer relay operation output
    Ignition switch ON, rear wiper switch on
    Below 1 V
    F8-2 (BW) - Body ground
    B - Body ground
    Rear washer relay operation output
    Ignition switch ON, rear wiper switch off
    11 to 14 V
    If the result is not as specified, the main body ECU (multiplex network body ECU) or driver side junction block assembly may have a malfunction.



  5. B199631E01
  6. Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    1. F10-8 (RWSW) - Body ground
    2. F10-17 (RWLS) - Body ground
    3. F9-1 (RWC1) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch ON, rear washer switch off



  7. B201885E01
  8. Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    1. F10-8 (RWSW) - Body ground
    2. F10-17 (RWLS) - Body ground
    3. F9-1 (RWC1) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Ignition switch ON, rear washer switch off


CHECK MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)

B241165E03

  1. Disconnect the V2 multiplex network door ECU (back door P/W) connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    V2-1 (BDR) - Body ground
    B - Body ground
    Battery power supply
    Always
    11 to 14 V
    V2-7 (BECU) - Body ground
    L - Body ground
    Battery power supply
    Always
    11 to 14 V
    V2-8 (SIG) - Body ground
    G - Body ground
    Ignition switch power supply
    Ignition switch ON
    11 to 14 V
    V2-8 (SIG) - Body ground
    G - Body ground
    Ignition switch power supply
    Ignition switch off
    Below 1 V
    V2-6 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the V2 multiplex network door ECU (back door P/W) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    V2-3 (W) - V2-12 (SGND)
    R - G
    Rear wiper reverse position switch input
    Ignition switch ON and rear wiper switch on (rear wiper reverse position switch off)
    Pulse generation (See waveform 1)
    V2-3 (W) - V2-12 (SGND)
    R - G
    Rear wiper reverse position switch input
    Ignition switch ON and rear wiper switch on (rear wiper reverse position switch on)
    Pulse generation (See waveform 2)
    V2-4 (P) - V2-12 (SGND)
    V - G
    Rear wiper retractable position switch input
    Ignition switch ON and rear wiper switch on (rear wiper retractable position switch off)
    Pulse generation (See waveform 3)
    V2-4 (P) - V2-12 (SGND)
    V - G
    Rear wiper retractable position switch input
    Ignition switch ON and rear wiper switch on (rear wiper retractable position switch on)
    Pulse generation (See waveform 4)
    V2-2 (WIP+) - V2-6 (GND)
    L - W-B
    Rear wiper motor output
    Ignition switch ON, rear wiper switch INT
    Pulse generation (See waveform 5)
    V2-5 (WIP-) - V2-6 (GND)
    P - W-B
    Rear wiper motor output
    Ignition switch ON, rear wiper switch INT
    Pulse generation (See waveform 6)
    V2-2 (WIP+) - V2-6 (GND)
    L - W-B
    Rear wiper motor output
    Ignition switch ON, rear wiper switch LO
    Pulse generation (See waveform 7)
    V2-5 (WIP-) - V2-6 (GND)
    P - W-B
    Rear wiper motor output
    Ignition switch ON, rear wiper switch LO
    Pulse generation (See waveform 8)
    V2-2 (WIP+) - V2-6 (GND)
    L - W-B
    Rear wiper motor output
    Ignition switch ON, rear washer switch on
    Pulse generation (See waveform 9)
    V2-5 (WIP-) - V2-6 (GND)
    P - W-B
    Rear wiper motor output
    Ignition switch ON, rear washer switch on
    Pulse generation (See waveform 10)
    V2-2 (WIP+) - V2-6 (GND)
    L - W-B
    Rear wiper motor output
    Ignition switch ON, rear wiper switch off
    Pulse generation (See waveform 11)
    V2-5 (WIP-) - V2-6 (GND)
    P - W-B
    Rear wiper motor output
    Ignition switch ON, rear wiper switch off
    Pulse generation (See waveform 12)
    If the result is not as specified, the multiplex network door ECU (back door P/W) may have a malfunction.



  5. B242627E01
  6. Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    V2-3 (W) - V2-12 (SGND)
    Tool Setting
    5 V/DIV., 10 ms/DIV
    Condition
    Ignition switch ON and rear wiper switch on (rear wiper reverse position switch off)



  7. B242628E01
  8. Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    V2-3 (W) - V2-12 (SGND)
    Tool Setting
    5 V/DIV., 10 ms/DIV
    Condition
    Ignition switch ON and rear wiper switch on (rear wiper reverse position switch on)



  9. B242627E01
  10. Using an oscilloscope, check waveform 3.
    Waveform 3 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    V2-4 (P) - V2-12 (SGND)
    Tool Setting
    2 V/DIV., 2 ms/DIV
    Condition
    Ignition switch ON and rear wiper switch on (rear wiper retractable position switch off)



  11. B242628E01
  12. Using an oscilloscope, check waveform 4.
    Waveform 4 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    V2-4 (P) - V2-12 (SGND)
    Tool Setting
    2 V/DIV., 2 ms/DIV
    Condition
    Ignition switch ON and rear wiper switch on (rear wiper retractable position switch on)



  13. B242631E01
  14. Using an oscilloscope, check waveform 5.
    Waveform 5 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    V2-2 (WIP+) - V2-6 (GND)
    Tool Setting
    2 V/DIV., 2 ms/DIV
    Condition
    Ignition switch ON, rear wiper switch INT



  15. B242632E01
  16. Using an oscilloscope, check waveform 6.
    Waveform 6 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    V2-5 (WIP-) - V2-6 (GND)
    Tool Setting
    2 V/DIV., 2 ms/DIV
    Condition
    Ignition switch ON, rear wiper switch INT



  17. B242635E01
  18. Using an oscilloscope, check waveform 7.
    Waveform 7 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    V2-2 (WIP+) - V2-6 (GND)
    Tool Setting
    2 V/DIV., 2 ms/DIV
    Condition
    Ignition switch ON, rear wiper switch LO



  19. B242636E01
  20. Using an oscilloscope, check waveform 8.
    Waveform 8 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    V2-5 (WIP-) - V2-6 (GND)
    Tool Setting
    2 V/DIV., 2 ms/DIV
    Condition
    Ignition switch ON, rear wiper switch LO



  21. B242639E01
  22. Using an oscilloscope, check waveform 9.
    Waveform 9 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    V2-2 (WIP+) - V2-6 (GND)
    Tool Setting
    2 V/DIV., 2 ms/DIV
    Condition
    Ignition switch ON, rear washer switch on



  23. B242640E01
  24. Using an oscilloscope, check waveform 10.
    Waveform 10 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    V2-5 (WIP-) - V2-6 (GND)
    Tool Setting
    2 V/DIV., 2 ms/DIV
    Condition
    Ignition switch ON, rear washer switch on



  25. B242643E01
  26. Using an oscilloscope, check waveform 11.
    Waveform 11 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    V2-2 (WIP+) - V2-6 (GND)
    Tool Setting
    2 V/DIV., 2 ms/DIV
    Condition
    Ignition switch ON, rear wiper switch off



  27. B242644E01
  28. Using an oscilloscope, check waveform 12.
    Waveform 12 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    V2-5 (WIP-) - V2-6 (GND)
    Tool Setting
    2 V/DIV., 2 ms/DIV
    Condition
    Ignition switch ON, rear wiper switch off