Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0125    Insufficient Coolant Temperature for Closed Loop Fuel Control

for Preparation Click here


DESCRIPTION

  1. Refer to DTC P0115 .

    DTC No.
    DTC Detection Condition
    Trouble Area
    P0125
    Engine coolant temperature does not reach the closed-loop enabling temperature for 20 minutes (this period varies with the engine coolant temperature at engine start) (2 trip detection logic).
    1. Engine coolant temperature sensor
    2. Cooling system
    3. Thermostat

MONITOR DESCRIPTION

The resistance of the engine coolant temperature sensor varies in proportion to the actual engine coolant temperature. The ECM supplies a constant voltage to the sensor and monitors the output signal voltage of the sensor. The output signal voltage varies according to the changing resistance of the sensor. After the engine is started, the engine coolant temperature is monitored through this signal. If the engine coolant temperature sensor indicates that the engine is not yet warm enough for closed-loop fuel control, despite a specified period of time having elapsed since the engine was started, the ECM interprets this as a malfunction in the sensor or cooling system and stores the DTC.
Example:
The engine coolant temperature is 0°C (32°F) at engine start. After approximately 1 minute of running time, the engine coolant temperature sensor still indicates that the engine is not warm enough to begin closed-loop fuel (air-fuel ratio feedback) control. The ECM interprets this as a malfunction in the sensor or cooling system and stores the DTC.

MONITOR STRATEGY


Related DTCs
P0125: Insufficient engine coolant temperature for closed-loop fuel control
Required Sensors/Components (Main)
Thermostat, cooling system
Required Sensors/Components (Related)
Engine coolant temperature sensor and mass air flow meter
Frequency of Operation
Once per driving cycle
Duration
56 seconds: Engine coolant temperature at engine start -8.33°C (17°F) or higher
101 seconds: Engine coolant temperature at engine start between -8.33°C (17°F) and -19.44°C (-3°F)
1200 seconds: Engine coolant temperature at engine start less than -19.44°C (-3°F)
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
P0101, P0102, P0103 (Mass Air Flow Sensor)
P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0128 (Thermostat)

TYPICAL MALFUNCTION THRESHOLDS


Engine coolant temperature (closed-loop fuel control enabling temperature)
56 seconds: Engine coolant temperature at engine start -8.33°C (17°F) or higher
101 seconds: Engine coolant temperature at engine start between -8.33°C (17°F) and -19.44°C (-3°F)
1200 seconds: Engine coolant temperature at engine start less than -19.44°C (-3°F)

CONFIRMATION DRIVING PATTERN

  1. Leave the vehicle outside overnight.
  2. Connect the Techstream to the DLC3.
  3. Turn the ignition switch to ON and turn the Techstream on.
  4. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  5. Read the DTC and record the Freeze Frame Data.
  6. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).
  7. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
  8. Check that the Coolant Temp is the same or less than Initial Engine Coolant Temp in the Freeze Frame Data.
  9. Turn the ignition switch off and wait for at least 30 seconds.
  10. Turn the ignition switch to ON and turn the Techstream on.
  11. Start the engine.
  12. Wait 20 minutes or more.
  13. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  14. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  15. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  16. Input the DTC: P0125.
  17. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  18. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

HINT:
  1. If DTC P0115, P0116, P0117 or P0118 is stored simultaneously with DTC P0125, the engine coolant temperature sensor may have an open or short circuit. Troubleshoot those DTCs first.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0125)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.

  1. Read DTCs.

    Result 
    Display (DTC Output)
    Proceed to
    P0125
    A
    P0125 and other DTCs
    B

    HINT:
    If any DTCs other than P0125 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INSPECT THERMOSTAT
  1. Remove the thermostat (Click here).

  1. Check the valve opening temperature of the thermostat.

    Standard value:
    80 to 84°C (176 to 183°F)

    HINT:
    In addition to the above check, confirm that the valve is completely closed when the temperature is below the standard.

  1. Reinstall the thermostat (Click here).



NG
REPLACE THERMOSTAT (Click here)
OK


3.CHECK COOLING SYSTEM
  1. Check for defects in the cooling system that might cause the system to be too cold, such as abnormal radiator fan operation or any modifications.



NG
REPAIR OR REPLACE COOLING SYSTEM
OK

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)