Home › Drivetrain · A750E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0717    Turbine Speed Sensor Circuit No Signal

for Preparation Click here


DESCRIPTION

This sensor detects the rotation speed of the turbine which indicates the input speed of the transmission. By comparing the input turbine speed signal NT with the counter gear speed sensor signal SP2, the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions. As a result, the gears shift smoothly.

DTC Code
DTC Detection Condition
Trouble Area
P0717
All conditions are met for 5 sec. or more (1-trip detection logic):
(a) Gear change: not performed.
(b) Gear position: 4th or 5th.
(c) T/M input shaft speed: 300 rpm or less.
(d) T/M output shaft speed: 1000 rpm or more.
(e) Park/neutral position switch: R input signal is OFF.
(f) Shift solenoid valves and park/neutral position switch: in normal operation.
  1. Open or short in speed sensor NT circuit
  2. Speed sensor NT
  3. ECM
  4. Automatic transmission (clutch, brake, gear, etc.)
Reference: Inspect using an oscilloscope.
Check the waveform of the ECM connector.

Standard:
Terminal No. (Symbol)
Tool Setting
Condition
Specified Condition
B38-3 (NT+) - B38-4 (NT-)
1 V/DIV., 2 msec./DIV.
Engine idling (shift lever in P or N)
Refer to illustration

C162170E01

MONITOR DESCRIPTION

This DTC indicates that a pulse is not output from the speed sensor NT (turbine (input) speed sensor) or is output only a little. The NT terminal of the ECM detects the pulse signal from the speed sensor NT (input RPM). The ECM outputs a gear shift signal by comparing the input speed sensor NT signal with the output speed sensor SP2 signal.
While the vehicle is operating in 4th or 5th gear with the shift lever in D, if the input shaft speed is less than 300 rpm*1 although the output shaft speed is 1000 rpm or more*2, the ECM detects the trouble, illuminates the MIL and stores the DTC.

HINT:
  1. *1: A pulse is not output or is irregularly output.
  2. *2: The vehicle speed is approximately 50 km/h (30 mph) or more.


MONITOR STRATEGY


Related DTCs
P0717: Speed sensor (NT)/Verify pulse input
Required sensors/Components (Main)
Speed sensor (NT)
Required sensors/Components (Related)
Speed sensor (NC)
Frequency of operation
Continuous
Duration
5 sec.
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the following DTCs are not stored
P0705 (Park/neutral position switch circuit)
P0746, P0748 (Shift solenoid valve SL1)
P0776, P0778 (Shift solenoid valve SL2)
P0751, P0973, P0974 (Shift solenoid valve S1)
P0756, P0976, P0977 (Shift solenoid valve S2)
Shift change
Shift change is completed and before starting next shift change operation
ECM selected gear
4th or 5th
Output shaft rpm
1000 rpm or more
R switch
OFF
Engine
Running
Battery voltage
8 V or higher
Ignition switch
ON
Starter
OFF

TYPICAL MALFUNCTION THRESHOLDS


Speed sensor signal rpm
Less than 300 rpm

COMPONENT OPERATING RANGE


Speed sensor signal rpm
300 rpm or more

WIRING DIAGRAM


C155187E67


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).


DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the Techstream, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    SPD (NT)
    Input shaft speed/
    Min.: 0 rpm
    Max.: 12750 rpm
    1. Lock-up ON (after warming up engine): Input turbine speed (NT) is equal to engine speed
    2. Lock-up OFF (idling with shift lever in N): Input turbine speed (NT) is nearly equal to engine speed
    Data is displayed in increments of 50 rpm.

    HINT:
    1. SPD (NT) is always 0 while driving:
      Open or short in the sensor or circuit.
    2. SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (30 mph) or more:
      Sensor trouble, improper installation or intermittent connection trouble in the circuit.

1.INSPECT SPEED SENSOR NT INSTALLATION


    C211922E01
  1. Check the speed sensor NT installation.

    OK:
    The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.

    Text in Illustration 
    *a
    CORRECT
    *b
    INCORRECT



NG
SECURELY INSTALL OR REPLACE SPEED SENSOR NT
OK


2.INSPECT SPEED SENSOR NT


    C206284E05
  1. Disconnect the B34 speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    560 to 680 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Speed Sensor NT)



NG
REPLACE SPEED SENSOR NT
OK


3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR NT - ECM)


    C214337E01
  1. Disconnect the B38 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B38-3 (NT+) - B38-4 (NT-)
    20°C (68°F)
    560 to 680 Ω
    B38-3 (NT+) - Body ground
    Always
    10 kΩ or higher
    B38-4 (NT-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)