Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)

AIR CONDITIONING SYSTEM (for Manual Air Conditioning System) > Air Conditioning Compressor Magnetic Clutch Circuit

for Preparation Click here


DESCRIPTION

When the air conditioning amplifier assembly is turned on, a magnet clutch assembly ON signal is sent from the MGC terminal of the air conditioning amplifier assembly. Then, the A/C COMP relay turns on to operate the magnet clutch assembly.

WIRING DIAGRAM


E198320E03


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.INSPECT MAGNET CLUTCH RELAY (A/C COMP)


    E145138
  1. Remove the A/C COMP relay from the engine room No. 1 relay block, junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE MAGNET CLUTCH RELAY (A/C COMP)
OK


2.INSPECT COOLER COMPRESSOR ASSEMBLY


    E198321E01
  1. Remove the cooler compressor assembly (Click here).

  1. Disconnect the A magnet clutch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (MG+) - A-1
    Always
    Below 1 Ω
    3 (MG+) - Body ground
    Always
    10 kΩ or higher



NG
REPLACE COOLER COMPRESSOR ASSEMBLY (Click here)
OK


3.INSPECT MAGNETIC CLUTCH ASSEMBLY


    E198322E01
  1. Reconnect the A magnet clutch connector.

  1. Apply battery voltage to the magnet clutch assembly and check the operation of the magnet clutch assembly.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 3 (MG+)
    Battery negative (-) → Body ground
    Magnet clutch assembly operating sound can be heard, and magnetic clutch hub and rotor lock.



NG
REPLACE MAGNET CLUTCH ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - BATTERY)


    E200501E01
  1. Remove the A/C COMP relay from the engine room No. 1 relay block, junction block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A/C COMP relay terminal 1 - Body ground
    Ignition switch ON
    11 to 14 V
    A/C COMP relay terminal 5 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    A/C COMP Relay
    *a
    Component without relay installed
    (Engine Room No. 1 Relay Block, Junction Block)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)


    E177002E82
  1. Disconnect the F42 amplifier connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F42-20 (MGC) - Body ground
    Ignition switch off
    Below 1 V
    F42-20 (MGC) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Conditioning Amplifier Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - COOLER COMPRESSOR)
  1. Remove the A/C COMP relay from the engine room No. 1 relay block, junction block.

  1. Disconnect the B41 compressor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A/C COMP relay terminal 3 - B41-3 (MG+)
    Always
    Below 1 Ω
    B41-3 (MG+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)