Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM (for Start Function)

DTC    B2284    Brake Signal Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when the brake signal information from the cable and the brake signal information from the CAN communication line are inconsistent

HINT:
When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode is reset to on (IG). When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.


DTC Code
DTC Detection Condition
Trouble Area
B2284
The brake signal information from the cable and the brake signal information from the CAN communication line are inconsistent.
  1. STOP fuse
  2. AM2 fuse
  3. Stop light switch assembly
  4. SFI system
  5. Power management control ECU
  6. Harness or connector

WIRING DIAGRAM


B353566E01


INSPECTION PROCEDURE

NOTICE:
  1. When using the Techstream with the engine switch off to troubleshoot: Connect the Techstream to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.
  2. Before performing the inspection, check that there are no problems related to the CAN communication system and LIN communication system.
  3. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.

1.CHECK HARNESS AND CONNECTOR (BATTERY - POWER MANAGEMENT CONTROL ECU)


    A207890E08
  1. Disconnect the F80 power management control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F80-2 (AM21) - Body ground
    Always
    9.5 to 14 V
    F80-1 (AM22) - Body ground

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)
  1. Disconnect the F80 power management control ECU connector.



    A207890E09
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F80-6 (GND) - Body ground
    Always
    Below 1 Ω
    F80-5 (GND2) - Body ground

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT STOP LIGHT SWITCH ASSEMBLY
  1. Inspect the stop light switch assembly (Click here).



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)
  1. Disconnect the F81 power management control ECU connector.

  1. Disconnect the A47 stop light switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F81-11 (STP1) - A47-3 (L)
    Always
    Below 1 Ω
    F81-11 (STP1) - Body ground
    Always
    10 kΩ or higher



    C216309E04
  1. Reconnect the A47 stop light switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F81-11 (STP1) - Body ground
    Brake pedal not depressed
    Below 1 V
    Brake pedal depressed
    ([Voltage at terminal AM21 or AM22] minus 2.0 V) or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Power Source Control / Data List.

  1. According to the display on the Techstream, read the Data List.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light Switch1
    Stop light switch 1 / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

    OK:
    ON (brake pedal depressed) or OFF (brake pedal released) appears on the screen according to the stop light switch condition.



NG
GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)