Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM

DTC    C2165/65    Abnormal Temperature Inside ID1 Tire

DTC    C2166/66    Abnormal Temperature Inside ID2 Tire

DTC    C2167/67    Abnormal Temperature Inside ID3 Tire

DTC    C2168/68    Abnormal Temperature Inside ID4 Tire

for Preparation Click here


DESCRIPTION

Each tire pressure warning valve and transmitter measures the internal temperature of its tire as well as the tire pressure and transmits the information to the tire pressure warning ECU along with the transmitter ID. If the measured temperature is out of the specified range, the tire pressure warning ECU recognizes it as a malfunction and stores DTCs, and the tire pressure warning light blinks for 1 minute and then remains on.

DTC Code
Detection Condition
Trouble Area
C2165/65
C2166/66
C2167/67
C2168/68
The temperature inside the tire is detected as being higher than 119°C (246°F) 255 times consecutively.
  1. Tires
  2. Tire pressure warning valve and transmitter
  3. Tire pressure warning ECU

HINT:
It is necessary to perform the procedure to identify the tire pressure warning valve and transmitter that is malfunctioning because it cannot be identified by the output DTC.


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the tire pressure warning ECU, read the IDs stored in the old ECU using the Techstream and note them down before removal.
  2. It is necessary to perform registration of the transmitter IDs into the tire pressure warning ECU after the ECU and/or the tire pressure warning valve and transmitter has been replaced (Click here).

1.CHECK TIRES
  1. Check that the tires are not flat and have no indication of air pressure drop.

    OK:
    Tires are normal.

    HINT:
    If a tire is damaged, the tire pressure warning valve and transmitter may also have been damaged at the same time.



NG
REPLACE TIRE AND TIRE PRESSURE WARNING VALVE AND TRANSMITTER
OK


2.IDENTIFY TRANSMITTER CORRESPONDING TO DTC
  1. Set the tire pressure of all tires to the specified value (Click here).

  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  1. Check the "ID Tire Inflation Pressure" data for each wheel using the Techstream.

  1. Rapidly reduce the tire pressure of each tire by at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds.

  1. Check the Data List.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ID1 Tire Inflation Pressure
    ID1 tire inflation pressure /
    min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2, 0.0 psi), Relative pressure -100.0 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure 637.5 kPa (6.5 kgf/ cm2, 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0.0 kgf/cm2, 0.0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/ cm2, -14 psi) is displayed for relative pressure, data has not been received.*
    ID2 Tire Inflation Pressure
    ID2 tire inflation pressure /
    min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2, 0.0 psi), Relative pressure -100.0 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure 637.5 kPa (6.5 kgf/ cm2, 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0.0 kgf/cm2, 0.0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/ cm2, -14 psi) is displayed for relative pressure, data has not been received.*
    ID3 Tire Inflation Pressure
    ID3 tire inflation pressure /
    min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2, 0.0 psi), Relative pressure -100.0 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure 637.5 kPa (6.5 kgf/ cm2, 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0.0 kgf/cm2, 0.0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/ cm2, -14 psi) is displayed for relative pressure, data has not been received.*
    ID4 Tire Inflation Pressure
    ID4 tire inflation pressure /
    min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2, 0.0 psi), Relative pressure -100.0 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure 637.5 kPa (6.5 kgf/ cm2, 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0.0 kgf/cm2, 0.0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/ cm2, -14 psi) is displayed for relative pressure, data has not been received.*

    HINT:
    *: It may take approximately 2 or 3 minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2124/24 (Click here).


    Result 
    Result
    Detection Condition
    One of "ID Tire Inflation Pressure" data (ID1 to ID4) changed
    Normal
    No "ID Tire Inflation Pressure" data changed
    Transmitter corresponding to DTC

    NOTICE:
    1. It takes approximately 2 or 3 minutes to display the updated tire pressure data.
    2. When "ID Tire Inflation Pressure" data has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270°. Then forcibly transmit the transmitter ID and recheck.
    3. Record the transmitter ID and position of transmitters that are normal.

  1. When an "ID Tire Inflation Pressure" data value (ID1 to ID4) has changed, repeat this procedure for each tire.

  1. When all of the "ID Tire Inflation Pressure" data (ID1 to ID4) has changed, identify the malfunctioning tire pressure warning valve and transmitter using the recorded ID numbers and output DTC.


NEXT


3.REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER
  1. Replace the identified tire pressure warning valve and transmitter with a new one .

HINT:
  1. Before installing a new tire pressure warning valve and transmitter, read and write down its transmitter ID.
  2. The IDs for the tire pressure warning valves and transmitters that are not replaced should be checked using the Techstream and recorded.


NEXT


4.PERFORM REGISTRATION OF TRANSMITTER ID
  1. Register the transmitter IDs for all wheels (Click here).


NEXT


5.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  1. Check the values by referring to the table below.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ID1 Tire Inflation Pressure
    ID1 tire inflation pressure /
    min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2, 0.0 psi), Relative pressure -100.0 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0.0 kgf/cm2, 0.0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*
    ID2 Tire Inflation Pressure
    ID2 tire inflation pressure /
    min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2, 0.0 psi), Relative pressure -100.0 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0.0 kgf/cm2, 0.0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*
    ID3 Tire Inflation Pressure
    ID3 tire inflation pressure /
    min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2, 0.0 psi), Relative pressure -100.0 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0.0 kgf/cm2, 0.0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*
    ID4 Tire Inflation Pressure
    ID4 tire inflation pressure /
    min.: Absolute pressure 0.0 kPa (0.0 kgf/cm2, 0.0 psi), Relative pressure -100.0 kPa (-1.0 kgf/cm2, -14 psi)
    max.: Absolute pressure 637.5 kPa (6.5 kgf/cm2, 92 psi), Relative pressure 537.5 kPa (5.4 kgf/cm2, 78 psi)
    Actual tire inflation pressure
    If 0 kPa (0.0 kgf/cm2, 0.0 psi) is displayed for absolute pressure or -100 kPa (-1.0 kgf/cm2, -14 psi) is displayed for relative pressure, data has not been received.*

    HINT:
    1. *: It may take approximately 2 or 3 minutes until the values are displayed.
    2. When no "ID Tire Inflation Pressure" data has changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270°. Then rapidly release the tire pressure and recheck it.


    Result 
    Result
    Proceed to
    All tire pressure readings are equal to specified values
    A
    Tire pressure values are not displayed
    B



B
REPLACE TIRE PRESSURE WARNING ECU (Click here)
A

END