Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR (for Front Door)

POWER WINDOW REGULATOR MOTOR (for Front Door) > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH


    B240255
  1. Detach the 2 clips to remove the front door lower frame bracket garnish LH.



3. REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH


    B240256E01
  1. Using a moulding remover, detach the 3 claws to remove the No. 2 door inside handle bezel LH as shown in the illustration.
    Text in Illustration 
    *1
    Moulding Remover



4. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    B353477
  1. Detach the 4 claws to remove the 2 door armrest caps.



    B353478
  1. Remove the 3 screws.

  1. Detach the 11 clips.



    B353479E01
  1. Pull out the front door trim board sub-assembly LH in the direction indicated by the arrow shown in the illustration.

  1. Raise the front door trim board sub-assembly LH and detach the 4 claws and reference boss to remove the front door trim board sub-assembly LH together with the front door inner glass weatherstrip LH.
    Text in Illustration 
    *1
    Reference Boss



    B240574
  1. Disconnect the connector.



    B238525
  1. Disconnect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH.



5. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH


    B238526
  1. Using a screwdriver, detach the 4 claws to remove the front door inner glass weatherstrip LH from the front door trim board sub-assembly LH as shown in the illustration.



6. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY


    B240327
  1. Disconnect the speaker connector.

  1. Remove the 4 screws.

  1. Detach the 2 claws and remove the speaker.

    NOTICE:
    Do not touch the cone of the speaker.



7. REMOVE FRONT DOOR SERVICE HOLE COVER LH


    B240582
  1. Remove the bolt.

  1. Detach the 2 clamps and move the front door wire out of the way to remove the front door service hole cover LH.

    HINT:
    Remove any remaining butyl tape from the door panel.



8. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
  1. Connect the multiplex network master switch assembly (for Driver Side).

  1. Connect the power window regulator switch assembly (for Front Passenger Side).

  1. Connect the cable to the negative (-) battery terminal.

  1. Move the front door glass sub-assembly so that the front door glass bolts can be seen.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the multiplex network master switch assembly (for Driver Side).

  1. Disconnect the power window regulator switch assembly (for Front Passenger Side).



    B353480
  1. Remove the 2 bolts.

    NOTICE:
    Be careful when removing the bolts as the glass may fall and become damaged.



    B353481E01
  1. Remove the front door glass sub-assembly LH as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the front door glass sub-assembly LH.



9. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH


    B353482E01
  1. Disconnect the connector.

  1. Loosen the temporary bolt.
    Text in Illustration 
    *1
    Temporary Bolt

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator sub-assembly LH may fall and cause damage.

  1. Remove the 5 bolts.

  1. Remove the front door window regulator sub-assembly LH.

  1. Remove the temporary bolt from the front door window regulator sub-assembly LH.



10. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


    B238534

    B238976E03

  1. Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor.

    Text in Illustration 
    *1
    Spring
    -
    -
    *a
    Range of Movement
    -
    -

    CAUTION:
    Do not place your finger, etc. within the range of movement of the window regulator. When removing the power window regulator motor, the force of the spring causes the window regulator to move in the direction of the arrow shown in the illustration (the direction in which the window rises), which may cause injury.

    NOTICE:
    Be careful when removing the screws as the motor may fall and become damaged.