FRONT DOOR > DISASSEMBLY |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH |
![]() |
Detach the 2 clips to remove the front door lower frame bracket garnish LH.
| 3. REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH |
![]() |
Using a moulding remover, detach the 3 claws to remove the No. 2 door inside handle bezel LH as shown in the illustration.
| *1 | Moulding Remover |
| 4. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH |
![]() |
Detach the 4 claws to remove the 2 door armrest caps.
![]() |
Remove the 3 screws.
Detach the 11 clips.
![]() |
Pull out the front door trim board sub-assembly LH in the direction indicated by the arrow shown in the illustration.
Raise the front door trim board sub-assembly LH and detach the 4 claws and reference boss to remove the front door trim board sub-assembly LH together with the front door inner glass weatherstrip LH.
| *1 | Reference Boss |
![]() |
Disconnect the connector.
![]() |
Disconnect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH.
| 5. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH |
![]() |
Using a screwdriver, detach the 4 claws to remove the front door inner glass weatherstrip LH from the front door trim board sub-assembly LH as shown in the illustration.
| 6. REMOVE NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY (w/ Intuitive Parking Assist System) |
![]() |
Using a screwdriver, detach the claw and remove the light.
| *1 | Protective Tape |
Disconnect the connector.
| 7. REMOVE COURTESY LIGHT ASSEMBLY LH |
![]() |
Detach the 2 claws and remove the light.
Disconnect the connector.
Remove the bulb.
| 8. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (for Driver Side) |
![]() |
Disconnect the connector.
![]() |
Detach the 10 claws from the backside and remove the multiplex network master switch with base panel.
![]() |
Remove the 3 screws and multiplex network master switch assembly.
| 9. REMOVE DOOR CONTROL SWITCH ASSEMBLY (for Front Passenger Side) |
![]() |
Disconnect the door control switch connector.
Detach the 2 claws and remove the door control switch assembly.
| 10. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side) |
Detach the 10 claws from the backside and remove the power window regulator switch with base panel.

Disconnect the connectors.
![]() |
Detach the 2 claws and remove the power window regulator switch.
| 11. REMOVE SEAT MEMORY SWITCH (w/ Seat Position Memory System) |
![]() |
Disconnect the connector.
Remove the 2 screws.
Detach the 4 claws to remove the seat memory switch.
| 12. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY |
![]() |
Disconnect the speaker connector.
Remove the 4 screws.
Detach the 2 claws and remove the speaker.
| 13. REMOVE SIDE AIRBAG SENSOR ASSEMBLY LH |
![]() |
Disconnect the connector.
Remove the bolt and side airbag sensor.
| 14. REMOVE FRONT DOOR SERVICE HOLE COVER LH |
![]() |
Remove the bolt.
Detach the 2 clamps and move the front door wire out of the way to remove the front door service hole cover LH.
| 15. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH |
![]() |
Disconnect the connector.
Detach the clamp to remove the 3 nuts.
Detach the claw to remove the outer rear view mirror assembly LH.
| 16. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH |
Connect the multiplex network master switch assembly (for Driver Side).
Connect the power window regulator switch assembly (for Front Passenger Side).
Connect the cable to the negative (-) battery terminal.
Move the front door glass sub-assembly so that the front door glass bolts can be seen.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the multiplex network master switch assembly (for Driver Side).
Disconnect the power window regulator switch assembly (for Front Passenger Side).
![]() |
Remove the 2 bolts.
![]() |
Remove the front door glass sub-assembly LH as indicated by the arrows in the order shown in the illustration.
| 17. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH |
![]() |
Disconnect the connector.
Loosen the temporary bolt.
| *1 | Temporary Bolt |
Remove the 5 bolts.
Remove the front door window regulator sub-assembly LH.
Remove the temporary bolt from the front door window regulator sub-assembly LH.
| 18. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH |
![]() ![]() |
Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor.
| *1 | Spring | - | - |
| *a | Range of Movement | - | - |
| 19. REMOVE DOOR FRAME GARNISH LH |
![]() |
Detach the clip to remove the door frame garnish LH.
| 20. REMOVE FRONT DOOR GLASS RUN LH |
![]() |
Remove the front door glass run LH.
| 21. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH |
![]() |
Remove the bolt and front door rear lower frame sub-assembly LH as shown in the illustration.
| 22. REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side) |
![]() |
Remove the hole plug.
![]() |
Using a T30 "TORX" socket wrench, loosen the screw to remove the front door outside handle cover with lock cylinder assembly.
| 23. REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH (for Driver Side) |
![]() |
Using a screwdriver, detach the claw to remove the front door outside handle cover LH from the lock cylinder assembly.
| 24. REMOVE FRONT DOOR OUTSIDE HANDLE COVER RH (for Front Passenger Side) |
![]() |
Remove the hole plug.
![]() |
Using a T30 "TORX" socket wrench, loosen the screw to remove the front door outside handle cover RH.
| 25. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH |
w/ Smart Key System:
![]() |
Detach the 2 claws.
Disconnect the connector.
![]() |
Move the lever in the direction indicated by the arrow in the illustration.
![]() |
Remove the front door outside handle assembly LH as shown in the illustration.
| 26. REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD LH |
![]() |
Detach the guide and 2 claws to remove the front door front outside handle pad LH.
| 27. REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD LH |
![]() |
Detach the 2 claws to remove the front door rear outside handle pad LH.
| 28. REMOVE FRONT DOOR LOCK ASSEMBLY LH |
Disconnect the connector.
![]() |
Using a T30 "TORX" wrench, remove the 3 screws.
Slide the front door lock assembly downward, pull out the front door lock open rod from the outside handle frame, and remove the front door lock assembly and cables as a unit.
Remove the front door lock open rod from the front door lock assembly.
Remove the door lock wiring harness seal from the front door lock assembly.
| 29. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH |
![]() |
Remove the front door lock remote control cable assembly LH from the front door lock assembly LH.
| 30. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH |
![]() |
Using a screwdriver, detach the 3 claws to open the cover.
![]() |
Remove the front door inside locking cable assembly LH from the front door lock assembly LH.
| 31. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH |
w/ Smart Key System:
![]() |
Disconnect the connector.
Detach the clamp.
![]() |
Using a T30 "TORX" socket wrench, loosen the screw.
Slide the front door outside handle frame sub-assembly LH to detach the door handle nut and claw of the front door outside handle frame sub-assembly LH. Then remove the front door outside handle frame sub-assembly LH.
| 32. REMOVE FRONT DOOR NO. 2 WIRE LH (w/ Smart Key System) |
![]() |
Detach the 4 clamps to remove the front door No. 2 wire LH.
| 33. REMOVE FRONT DOOR LOCK OPEN ROD LH |
![]() |
Remove the front door lock open rod LH as indicated by the arrows in the order shown in the illustration.
| 34. REMOVE FRONT DOOR NO. 2 STIFFENER CUSHION |
![]() |
Remove the 2 bolts.
| *1 | Double-sided Tape |
Detach the 2 clamps to remove the front door No. 2 stiffener cushion.
| 35. REMOVE FRONT DOOR CHECK ASSEMBLY LH |
![]() |
Remove the bolt, 2 nuts and front door check assembly LH.
| 36. REMOVE FRONT DOOR WEATHERSTRIP LH |
![]() |
Using a clip remover, detach the 21 clips to remove the front door weatherstrip LH.
| 37. REMOVE FRONT DOOR BELT MOULDING LH |
![]() |
Put protective tape around the belt moulding.
| *1 | Protective Tape |
Detach the 6 claws and remove the front door belt moulding.
| 38. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING LH |
![]() |
Remove the door window frame moulding clip.
![]() |
Put protective tape around the front door rear window frame moulding.
| *1 | Protective Tape |
| *2 | Double-sided Tape |
| *3 | Moulding Remover |
Using a moulding remover, detach the clip and remove the double-sided tape to remove the front door rear window frame moulding.
| 39. REMOVE NO. 1 BLACK OUT TAPE LH |
![]() |
Pull back an edge of the black out tape and pull it parallel to the vehicle body to remove it.
| 40. REMOVE FRONT DOOR OUTSIDE STRIPE LH |
![]() |
Pull back an edge of the front door outside stripe and pull it parallel to the vehicle body to remove it.
| 41. REMOVE FRONT DOOR LOWER OUTSIDE STRIPE LH |
![]() |
Pull back an edge of the lower front door outside stripe and pull it parallel to the vehicle body to remove it.
| 42. REMOVE FRONT DOOR PANEL CUSHION |
![]() |
Using a clip remover, detach the claw to remove the front door panel cushion.