Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR (for Front Door)

POWER WINDOW REGULATOR MOTOR (for Front Door) > INSTALLATION

for Preparation Click here



1. INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NOTICE:
The regulator arm must be below the intermediate position when installing the power window regulator motor.



    B238534E01
  1. Using a T25 "TORX" socket wrench, install the power window regulator motor with the 3 screws.

    HINT:
    1. Tighten the screws in the order shown in the illustration.
    2. A new front window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are installed.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



2. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
  1. Apply MP grease to the sliding parts of the front door window regulator sub-assembly LH.



    B353482E02
  1. Install the temporary bolt to the front door window regulator sub-assembly LH.
    Text in Illustration 
    *1
    Temporary Bolt

  1. Temporarily install the front door window regulator sub-assembly LH.

  1. Tighten the temporary bolt and 5 bolts to install the front door window regulator sub-assembly LH.

    HINT:
    Tighten the bolts in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH
  1. Connect the multiplex network master switch assembly (for Driver Side).

  1. Connect the power window regulator switch assembly (for Front Passenger Side).

  1. Connect the cable to the negative (-) battery terminal.

  1. Move the front door glass sub-assembly so that the front door glass bolts can be seen.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the multiplex network master switch assembly (for Driver Side).

  1. Disconnect the power window regulator switch assembly (for Front Passenger Side).



    B353492E01
  1. Insert the front door glass sub-assembly LH into the front door panel along the front door glass run LH as indicated by the arrows in the order shown in the illustration.



    B353480E01
  1. Install the front door glass sub-assembly LH with the 2 bolts in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



4. INSTALL FRONT DOOR SERVICE HOLE COVER LH
  1. Apply a new butyl tape to the front door panel.



    B240610E01
  1. Pass the front door lock remote control cable assembly LH and front door inside locking cable assembly LH through a new front door service hole cover LH.

  1. Install a new front door service hole cover LH according to the reference points on the front door panel.
    Text in Illustration 
    *1
    Reference Point

    NOTICE:
    Securely install the front door service hole cover LH preventing wrinkles and air bubbles.



    B240582
  1. Attach the 2 clamps.

  1. Connect the door wire with the bolt.



5. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY
  1. Temporarily install the speaker by attaching the 2 claws of the speaker to the door panel.

  1. Install the speaker with the 4 screws.

    Torque:
    2.5 N*m{ 25 kgf*cm , 22 in.*lbf }

    NOTICE:
    Do not touch the cone of the speaker.

  1. Connect the connector.



6. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH


    B240611
  1. Attach the 4 claws to install the front door inner glass weatherstrip LH as shown in the illustration.



7. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    B240612
  1. Connect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH.



    B240574
  1. Connect the connector.



    B354466E01
  1. Attach the front door trim board sub-assembly LH to the 4 claws of the front door inner glass weatherstrip LH as shown in the illustration.

  1. Attach the reference boss.
    Text in Illustration 
    *1
    Reference Boss



    B353478
  1. Attach the 11 clips to install the front door trim board sub-assembly LH.

  1. Install the 3 screws.



    B353477
  1. Attach the 4 claws to install the 2 door armrest caps.



8. INSTALL NO. 2 DOOR INSIDE HANDLE BEZEL LH


    B357472
  1. Attach the 3 claws to install the rear door inside handle bezel LH.



9. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH


    B240255
  1. Attach the 2 clips to install the front door lower frame bracket garnish LH.



10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



11. INITIALIZE POWER WINDOW CONTROL SYSTEM
  1. Initialize the power window control system (Click here).



12. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).