Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR (for Rear Door)

POWER WINDOW REGULATOR MOTOR (for Rear Door) > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH


    B240700E01
  1. Using moulding remover, detach the 3 claws to remove the rear door inside handle bezel LH as shown in the illustration.
    Text in Illustration 
    *1
    Moulding Remover



3. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    B240701
  1. Detach the 4 claws to remove the 2 door armrest caps.



    B240704
  1. Remove the 3 screws.

  1. Remove the 9 clips.



    B357470E01
  1. Pull out the rear door trim board sub-assembly LH in the direction indicated by the arrow as shown in the illustration.

  1. Raise the rear door trim board sub-assembly LH and detach the 4 claws and reference boss to remove the rear door trim board sub-assembly LH together with the rear door inner glass weatherstrip LH.
    Text in Illustration 
    *1
    Reference Boss



    B242772
  1. Disconnect the connector.



    B240708
  1. Disconnect the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH as shown in the illustration.



    B240710
  1. Using a screwdriver, detach the claw to remove the clamp.



4. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH


    B240709
  1. Using a screwdriver, detach the 3 claws to remove the rear door inner glass weatherstrip LH from the rear door trim board sub-assembly LH as shown in the illustration.



5. REMOVE REAR SPEAKER ASSEMBLY


    B240328
  1. Disconnect the speaker connector.

  1. Remove the 3 screws.

  1. Detach the 2 claws and remove the speaker.

    NOTICE:
    Do not touch the cone of the speaker.



6. REMOVE REAR DOOR SERVICE HOLE COVER LH


    B240711
  1. Disconnect the connector

  1. Detach the 3 clamps, move the rear door wire out of the way to remove the rear door service hole cover LH.

    HINT:
    Remove any remaining butyl tape from the rear door panel.



7. REMOVE REAR DOOR GLASS RUN LH


    B240715
  1. Remove the rear door glass run LH.



8. REMOVE REAR DOOR WINDOW REAR LOWER FRAME SUB-ASSEMBLY LH


    B240716E01
  1. Loosen the temporary bolt.
    Text in Illustration 
    *1
    Temporary Bolt

  1. Remove the 2 bolts and screw.

  1. Remove the rear door window rear lower frame sub-assembly LH.

    NOTICE:
    When the rear door window rear lower frame sub-assembly LH is removed, do not allow the rear door quarter window glass LH to fall.

  1. Remove the temporary bolt from the rear door window rear lower frame sub-assembly LH.



9. REMOVE REAR DOOR QUARTER WINDOW GLASS LH


    B240717
  1. Remove the rear door quarter window glass LH and rear door quarter window weatherstrip LH as a unit as shown in the illustration.



10. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH
  1. Connect the rear power window regulator switch assembly.

  1. Connect the cable to the negative (-) battery terminal.

  1. Move the arm of the rear door window regulator sub-assembly LH so that the roller on the arm can be seen through the service hole.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the rear power window regulator switch assembly.



    B240719
  1. Remove the rear door glass sub-assembly LH from the rear door window regulator sub-assembly LH as shown in the illustration.



    B240721E01
  1. Remove the rear door glass sub-assembly LH as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the rear door glass sub-assembly LH.



11. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH


    B240723E01
  1. Disconnect the connector.

  1. Loosen the temporary bolt.
    Text in Illustration 
    *1
    Temporary Bolt

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator sub-assembly LH may fall and cause damage.

  1. Remove the 3 bolts.

  1. Remove the rear door window regulator sub-assembly LH.

  1. Remove the temporary bolt from the rear door window regulator sub-assembly LH.



12. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


    B240724
  1. Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor.