Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR

REAR DOOR > DISASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure listed below is for the LH side.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE REAR DOOR INSIDE HANDLE BEZEL LH


    B240700E01
  1. Using moulding remover, detach the 3 claws to remove the rear door inside handle bezel LH as shown in the illustration.
    Text in Illustration 
    *1
    Moulding Remover



3. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    B240701
  1. Detach the 4 claws to remove the 2 door armrest caps.



    B240704
  1. Remove the 3 screws.

  1. Remove the 9 clips.



    B357470E01
  1. Pull out the rear door trim board sub-assembly LH in the direction indicated by the arrow as shown in the illustration.

  1. Raise the rear door trim board sub-assembly LH and detach the 4 claws and reference boss to remove the rear door trim board sub-assembly LH together with the rear door inner glass weatherstrip LH.
    Text in Illustration 
    *1
    Reference Boss



    B242772
  1. Disconnect the connector.



    B240708
  1. Disconnect the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH as shown in the illustration.



    B240710
  1. Using a screwdriver, detach the claw to remove the clamp.



4. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH


    B240709
  1. Using a screwdriver, detach the 3 claws to remove the rear door inner glass weatherstrip LH from the rear door trim board sub-assembly LH as shown in the illustration.



5. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY


  1. Detach the 10 claws from the backside and remove the power window regulator switch with base panel.


    B242795

  1. Disconnect the connector.



    B240703
  1. Detach the 2 claws and remove the power window regulator switch.



6. REMOVE COURTESY LIGHT ASSEMBLY


    E199241
  1. Detach the 2 claws and remove the light.

  1. Disconnect the connector.

  1. Remove the bulb.



7. REMOVE NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY (w/ Intuitive Parking Assist System)


    E200690E01
  1. Using a screwdriver, detach the claw and remove the light.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. Disconnect the connector.



8. REMOVE REAR SPEAKER ASSEMBLY


    B240328
  1. Disconnect the speaker connector.

  1. Remove the 3 screws.

  1. Detach the 2 claws and remove the speaker.

    NOTICE:
    Do not touch the cone of the speaker.



9. REMOVE REAR DOOR SERVICE HOLE COVER LH


    B240711
  1. Disconnect the connector

  1. Detach the 3 clamps, move the rear door wire out of the way to remove the rear door service hole cover LH.

    HINT:
    Remove any remaining butyl tape from the rear door panel.



10. REMOVE REAR DOOR FRAME GARNISH LH


    B240621
  1. Detach the clip to remove the rear door frame garnish LH.



11. REMOVE REAR DOOR GLASS RUN LH


    B240715
  1. Remove the rear door glass run LH.



12. REMOVE REAR DOOR WINDOW REAR LOWER FRAME SUB-ASSEMBLY LH


    B240716E01
  1. Loosen the temporary bolt.
    Text in Illustration 
    *1
    Temporary Bolt

  1. Remove the 2 bolts and screw.

  1. Remove the rear door window rear lower frame sub-assembly LH.

    NOTICE:
    When the rear door window rear lower frame sub-assembly LH is removed, do not allow the rear door quarter window glass LH to fall.

  1. Remove the temporary bolt from the rear door window rear lower frame sub-assembly LH.



13. REMOVE REAR DOOR QUARTER WINDOW GLASS LH


    B240717
  1. Remove the rear door quarter window glass LH and rear door quarter window weatherstrip LH as a unit as shown in the illustration.



14. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP LH
  1. Remove the rear door quarter window weatherstrip LH from the rear door quarter window glass LH.



15. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH
  1. Connect the rear power window regulator switch assembly.

  1. Connect the cable to the negative (-) battery terminal.

  1. Move the arm of the rear door window regulator sub-assembly LH so that the roller on the arm can be seen through the service hole.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the rear power window regulator switch assembly.



    B240719
  1. Remove the rear door glass sub-assembly LH from the rear door window regulator sub-assembly LH as shown in the illustration.



    B240721E01
  1. Remove the rear door glass sub-assembly LH as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the rear door glass sub-assembly LH.



16. REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY LH


    B234457E02
  1. Using a screwdriver, remove the rear door glass channel sub-assembly LH.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



17. REMOVE REAR DOOR GLASS CHANNEL FILLER
  1. Remove the rear door glass channel filler.



18. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH


    B240723E01
  1. Disconnect the connector.

  1. Loosen the temporary bolt.
    Text in Illustration 
    *1
    Temporary Bolt

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator sub-assembly LH may fall and cause damage.

  1. Remove the 3 bolts.

  1. Remove the rear door window regulator sub-assembly LH.

  1. Remove the temporary bolt from the rear door window regulator sub-assembly LH.



19. REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


    B240724
  1. Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor.



20. REMOVE REAR DOOR LOCK ASSEMBLY LH


    B237419
  1. Using a T30 "TORX" wrench, remove the 3 screws.

  1. Move the rear door lock assembly downward, pull the release plate out of the rear door outside handle frame, and remove the rear door lock assembly and cables as a unit.

  1. Remove the door lock wiring harness seal from the rear door lock assembly.



21. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    B240728
  1. Using a screwdriver, detach the claw to open the cover.

    HINT:
    Tape the screwdriver tip before use.



    B240729
  1. Remove the rear door lock remote control cable assembly LH from the rear door lock assembly LH.



22. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    B240730
  1. Using a screwdriver, detach the 3 claws to open the cover.

    HINT:
    Tape the screwdriver tip before use.



    B240731
  1. Remove the rear door inside locking cable assembly LH from the rear door lock assembly LH.



23. REMOVE REAR DOOR OUTSIDE HANDLE COVER LH


    B240732
  1. Using a T30 "TORX" socket wrench, loosen the screw.

    HINT:
    The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly LH.

  1. Detach the claw to remove the rear door outside handle cover LH.



24. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH


    B240733
  1. Move the lever in the direction indicated by the arrow in the illustration.



    B240735
  1. Remove the rear door outside handle assembly LH as shown in the illustration.



25. REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD


    B240737
  1. Detach the 3 claws to remove the rear door front outside handle pad.



26. REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD


    B240738
  1. Detach the 2 claws to remove the rear door rear outside handle pad.



27. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH


    B240739
  1. Using a T30 "TORX" socket wrench, loosen the screw.

  1. Slide the rear door outside handle frame sub-assembly LH to detach the door handle nut and claw of the rear door outside handle frame sub-assembly LH. Then remove the rear door outside handle frame sub-assembly LH.



28. REMOVE REAR DOOR CHECK ASSEMBLY LH


    B240713
  1. Remove the bolt, 2 nuts and rear door check assembly LH.



29. REMOVE REAR DOOR WEATHERSTRIP LH


    B240714
  1. Using a clip remover, detach the 20 clips to remove the rear door weatherstrip LH.



30. REMOVE REAR DOOR PANEL CUSHION


    B240622
  1. Using a clip remover, detach the claw to remove the rear door panel cushion.



31. REMOVE REAR DOOR BELT MOULDING LH


B242552E01
  1. Detach the 7 claws and remove the rear door belt moulding.
    Text in Illustration 
    *1
    Protective Tape



32. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING LH


B242554
  1. Remove the door window frame moulding clip.

  1. Detach the clip and remove the double-sided tape to remove the rear door front window frame moulding.



33. REMOVE NO. 2 BLACK OUT TAPE LH


B243002
  1. Pull back an edge of the No. 2 black out tape and pull it parallel to the vehicle body to remove it.



34. REMOVE REAR DOOR LOWER OUTSIDE STRIPE LH


B243004
  1. Pull back an edge of the rear door lower outside stripe and pull it parallel to the vehicle body to remove it.



35. REMOVE REAR DOOR OUTSIDE STRIPE LH


B243003
  1. Pull back an edge of the rear door outside stripe and pull it parallel to the vehicle body to remove it.



36. REMOVE REAR DOOR OUTSIDE MOULDING LH


    B239369E01
  1. Put protective tape around the rear door outside moulding LH.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 7 clips and 2 claws to remove the rear door outside moulding LH.

  1. Remove the 7 clips.



37. REMOVE REAR DOOR OUTSIDE MOULDING LH (w/ Intuitive Parking Assist System)


    B353450E01
  1. Put protective tape around the rear door outside moulding LH.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 7 clips and 2 claws to remove the rear door outside moulding LH.

  1. Remove the 7 clips.



38. REMOVE NO. 3 OUTSIDE MOULDING RETAINER


    B239372
  1. Remove the screw.

  1. Detach the claw to remove the No. 3 outside moulding retainer.