Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR

REAR DOOR > REASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure listed below is for the LH side.



1. INSTALL NO. 3 OUTSIDE MOULDING RETAINER
  1. Attach the claw to install the No. 3 outside moulding retainer.

  1. Install the screws.



2. INSTALL REAR DOOR OUTSIDE MOULDING LH
  1. Install new 7 clips to the rear door outside moulding LH.

  1. Attach the 7 clips and 2 claws to install the rear door outside moulding LH.



3. INSTALL REAR DOOR OUTSIDE MOULDING LH (w/ Intuitive Parking Assist System)
  1. Install new 7 clips to the rear door outside moulding LH.

  1. Attach the 7 clips and 2 claws to install the rear door outside moulding LH.



4. INSTALL REAR DOOR OUTSIDE STRIPE LH


B242549E01
  1. Refer to the illustration to position a new rear door outside stripe.

    Reference Value:
    Area
    Specified Condition
    A
    2 to 4 mm (0.078 to 0.158 in.)
    B
    4 to 6 mm (0.157 to 0.236 in.)
    C
    4 to 6 mm (0.157 to 0.236 in.)
    D
    2 to 4 mm (0.078 to 0.158 in.)
    E
    4 to 6 mm (0.157 to 0.236 in.)
    F
    2 to 4 mm (0.078 to 0.158 in.)



5. INSTALL REAR DOOR LOWER OUTSIDE STRIPE LH


B242551E01
  1. Refer to the illustration to position a new rear door lower outside stripe.

    Reference Value:
    Area
    Specified Condition
    A
    +/- 1.0 mm (0.039 in.) From End



6. INSTALL NO. 2 BLACK OUT TAPE LH


B242550E01
  1. Refer to the illustration to position new No. 2 black out tape.

    Reference Value:
    Area
    Specified Condition
    A
    +/- 1.0 mm (0.039 in.) From End
    B
    +/- 1.0 mm (0.039 in.) From End



7. INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING LH
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the double-sided tape from the vehicle body surface.

    3. Wipe off any tape adhesive residue with cleaner.

  1. Install a new rear door front window frame moulding.

    1. Using a heat light, heat a new rear door front window frame moulding and the vehicle body surface.

    2. Remove the peeling paper from the face of the rear door front window frame moulding.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    3. Attach the clip and double-sided tape to install the rear door front window frame moulding.

      HINT:
      Press the rear door front window frame moulding firmly to install it.

  1. Install a new door window frame moulding clip.



8. INSTALL REAR DOOR BELT MOULDING LH
  1. Attach the 7 claws to install the rear door belt moulding.



9. INSTALL REAR DOOR PANEL CUSHION


    B240622
  1. Attach the claw to install a new rear door panel cushion.



10. INSTALL REAR DOOR WEATHERSTRIP LH


    B240714
  1. Attach the 20 clips to install the rear door weatherstrip LH.



11. INSTALL REAR DOOR CHECK ASSEMBLY LH
  1. Apply MP grease to the sliding areas of the rear door check assembly LH.



    A057108E13
  1. Apply a few drops of adhesive to 2 or 3 threads of the bolt.
    Text in Illustration 
    *1
    Adhesive

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    NOTICE:
    Install the bolt within 3 minutes of applying adhesive.



    B240713
  1. Install the rear door check assembly LH to the rear door panel with the 2 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the rear door check assembly LH to the vehicle body with the bolt.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }



12. INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH
  1. Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly LH.



    B240748
  1. Attach the door handle nut and claw.

  1. Using a T30 "TORX" socket wrench, install the rear door outside handle frame sub-assembly LH with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



13. INSTALL REAR DOOR REAR OUTSIDE HANDLE PAD


    B240738
  1. Attach the 2 claws to install the rear door rear outside handle pad.



14. INSTALL REAR DOOR FRONT OUTSIDE HANDLE PAD


    B240737
  1. Attach the 3 claws to install the rear door front outside handle pad.



15. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY LH


    B240736
  1. Insert the front end of the rear door outside handle assembly LH into the rear door outside handle frame sub-assembly LH.

    NOTICE:
    If the bell crank lever is not pulled and held when installing the rear door outside handle assembly LH, the bell crank lever will interfere with the rear door outside handle assembly LH and the release plate will be damaged.

  1. Insert the rear end of the rear door outside handle assembly LH into the rear door outside handle frame sub-assembly. Next, slide the rear door outside handle assembly LH toward the front of the vehicle to install it.



    B240734
  1. Move the lever back in the direction indicated by the arrow in the illustration to lock the rear door outside handle assembly LH.



16. INSTALL REAR DOOR OUTSIDE HANDLE COVER LH


    B240732
  1. Attach the claw to install the rear door outside handle cover LH.

  1. Using a T30 "TORX" socket wrench, install the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



17. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    B240731
  1. Install the rear door inside locking cable assembly LH to the rear door lock assembly LH.



    B240730
  1. Attach the 3 claws to close the cover.



18. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    B240729
  1. Install the rear door lock remote control cable assembly LH to the rear door lock assembly LH.



    B240728
  1. Attach the claw to close the cover.



19. INSTALL REAR DOOR LOCK ASSEMBLY LH

NOTICE:
  1. When reusing the removed rear door lock assembly, replace the door lock wiring harness seal on the connector with a new one.
  2. Do not allow grease or dust to adhere to the surface of the connector which contacts the door lock wiring harness seal.
  3. Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may allow water to enter into the connection. This may result in a malfunction of the rear door lock assembly.

  1. Apply MP grease to the sliding parts of the rear door lock assembly.

  1. Install a new door lock wiring harness seal to the rear door lock assembly.



    B239751
  1. Insert the rear door lock assembly into the rear door outside handle release plate, and set it in place on the rear door panel.

  1. Check that the rear door outside handle frame release plate is securely connected to the rear door lock assembly.

  1. Using a T30 "TORX" wrench, install the rear door lock assembly with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



20. INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NOTICE:
The regulator arm must be below the intermediate position when installing the rear power window regulator motor assembly.



    B240724E01
  1. Using a T25 "TORX" socket wrench, install the power window regulator motor with the 3 screws.

    HINT:
    1. Tighten the screws in the order shown in the illustration.
    2. A new power window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are installed.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



21. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
  1. Apply MP grease to the sliding parts of the rear door window regulator sub-assembly LH.

  1. Install the temporary bolt to the rear door window regulator sub-assembly LH.



    B240723E02
  1. Temporarily install the rear door window regulator sub-assembly LH.
    Text in Illustration 
    *1
    Temporary Bolt

  1. Tighten the temporary bolt and 3 bolts to install the rear door window regulator sub-assembly LH.

    HINT:
    Tighten the bolts in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



22. INSTALL REAR DOOR GLASS CHANNEL FILLER
  1. Apply soapy water to a new rear door glass channel filler.



    B234459E02
  1. Install the rear door glass channel filler to the position shown in the illustration.
    Standard 
    Area
    Specified Condition
    A
    6.8 mm (0.268 in.)
    B
    6.7 mm (0.264 in.)
    Text in Illustration 
    *a
    Front Side
    *b
    Rear Side



23. INSTALL REAR DOOR GLASS CHANNEL SUB-ASSEMBLY LH
  1. Apply soapy water to the rear door glass channel filler side of the rear door glass channel sub-assembly LH.



    B234461E02
  1. Using a plastic-faced hammer, install the rear door glass channel sub-assembly LH to the position shown in the illustration.
    Standard 
    Area
    Specified Condition
    A
    6.8 mm (0.268 in.)
    B
    6.7 mm (0.264 in.)
    Text in Illustration 
    *a
    Front Side
    *b
    Rear Side

    NOTICE:
    To prevent damaging the rear door glass sub-assembly LH, be careful not to strike the channel with too much force.



24. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH
  1. Connect the rear power window regulator switch assembly.

  1. Connect the cable to the negative (-) battery terminal.



    B242781
  1. Operate the rear power window regulator switch assembly until the rear door window regulator sub-assembly LH reaches bottom dead center.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the rear power window regulator switch assembly.

  1. Install the front side of the rear door glass run LH.



    B242788E01
  1. Apply MP grease to the sliding areas of the rear door glass channel sub-assembly LH as shown in the illustration.
    Text in Illustration 
    *a
    5.0 mm (0.197 in.)
    *b
    157 mm (6.181 in.)
    *c
    5.0 mm (0.197 in.)
    V100155
    MP grease



    B240720
  1. Slide the rear door glass sub-assembly LH as shown in the illustration to install it.



25. INSTALL REAR DOOR QUARTER WINDOW WEATHERSTRIP LH
  1. Install the rear door quarter window weatherstrip LH to the rear door quarter window glass LH.



26. INSTALL REAR DOOR QUARTER WINDOW GLASS LH


    B240718
  1. Install the rear door quarter window glass LH together with the rear door quarter window weatherstrip LH in the direction indicated by the arrow in the illustration.



27. INSTALL REAR DOOR WINDOW REAR LOWER FRAME SUB-ASSEMBLY LH


    B240716E01
  1. Install the temporary bolt to the rear door window rear lower frame sub-assembly LH.
    Text in Illustration 
    *1
    Temporary Bolt

  1. Temporarily install the rear door window rear lower frame sub-assembly LH to the rear door panel.

  1. Install the screw.

  1. Install the 2 bolts.

    Torque:
    6.2 N*m{ 63 kgf*cm , 55 in.*lbf }

  1. Tighten the temporary bolt to install the rear door window rear lower frame sub-assembly LH.

    Torque:
    6.2 N*m{ 63 kgf*cm , 55 in.*lbf }



28. INSTALL REAR DOOR GLASS RUN LH


    B240715
  1. Install the rear door glass run LH.



29. INSTALL REAR DOOR FRAME GARNISH LH


    B240621
  1. Attach the clip to install a new rear door frame garnish LH.



30. INSTALL REAR DOOR SERVICE HOLE COVER LH
  1. Apply a new butyl tape to the rear door panel.



    B240712E01
  1. Pass the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH through a new rear door service hole cover LH.

  1. Install the rear door service hole cover LH according to the reference points on the rear door panel.
    Text in Illustration 
    *1
    Reference Point

    NOTICE:
    Securely install the rear door service hole cover LH preventing wrinkles and air bubbles.

  1. Connect the connector.

  1. Attach the 3 clamps and rear door wire.



31. INSTALL REAR SPEAKER ASSEMBLY
  1. Temporarily install the speaker by attaching the 2 claws of the speaker to the door panel.

  1. Install the speaker with the 3 screws.

    Torque:
    2.5 N*m{ 25 kgf*cm , 22 in.*lbf }

    NOTICE:
    Do not touch the cone of the speaker.

  1. Connect the connector.



32. INSTALL NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY (w/ Intuitive Parking Assist System)


    E199229
  1. Connect the connector.

  1. Attach the claw to install the light.



33. INSTALL COURTESY LIGHT ASSEMBLY
  1. Install the bulb.

  1. Connect the connector.

  1. Attach the 2 claws to install the light.



34. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY
  1. Attach the 2 claws to install the power window regulator switch assembly to the base panel.

  1. Connect the connector.

  1. Attach the 10 claws to the install the power window regulator switch with base panel.



35. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH


    B240749
  1. Attach the 3 claws to install the rear door inner glass weatherstrip LH as shown in the illustration.



36. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    B240750
  1. Attach the claw to install the clamp.



    B242790
  1. Connect the rear door lock remote control cable assembly LH and rear door inside locking cable assembly LH as shown in the illustration.



    B242772
  1. Connect the connector.



    B357471E01
  1. Attach the rear door trim board sub-assembly LH to the 4 claws of the rear door inner glass weatherstrip LH as shown in the illustration.

  1. Attach the reference boss.
    Text in Illustration 
    *1
    Reference Boss



    B240704
  1. Attach the 9 clips to install the rear door trim board sub-assembly LH.

  1. Install the 3 screws.



    B357479
  1. Attach the 4 claws to install the 2 door armrest caps.



37. INSTALL REAR DOOR INSIDE HANDLE BEZEL LH


    B357472
  1. Attach the 3 claws to install the rear door inside handle bezel LH.



38. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



39. INITIALIZE POWER WINDOW CONTROL SYSTEM
(Click here)