Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM

NAVIGATION SYSTEM > Illumination Circuit

for Preparation Click here


DESCRIPTION

Power is supplied to the navigation receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM


E226612E26


INSPECTION PROCEDURE

NOTICE:
  1. The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (Click here).
  2. Inspect the fuse for circuits related to this system before performing the following inspection procedure.

1.CHECK ILLUMINATION
  1. Check if the illumination for the navigation receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

    Result:

    Result
    Proceed to
    Illumination comes on for all components except steering pad switch assembly.
    A
    Illumination comes on for all components except navigation receiver assembly.
    B
    Illumination comes on only for steering pad switch assembly.
    C
    No illumination comes on (navigation receiver assembly, hazard switch, heater control switch, etc.).
    D



B
Go to step 5

C
GO TO METER / GAUGE SYSTEM (Click here)

D
GO TO LIGHTING SYSTEM (Click here)
A


2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
  1. Disconnect the F23 spiral cable sub-assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F23-12 (IL+2) - Body ground
    Light control switch in the tail or head position
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT STEERING PAD SWITCH ASSEMBLY
  1. Remove the steering pad switch assembly .

  1. Inspect the steering pad switch assembly .



NG
REPLACE STEERING PAD SWITCH ASSEMBLY
OK


4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
  1. Inspect the spiral cable sub-assembly .

NOTICE:
  1. The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.
  2. As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.

HINT:
  1. Removal (Click here)
  2. Installation (Click here)



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND) 

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
  1. Disconnect the G6 navigation receiver assembly connector.



    E178447E75
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G6-10 (ILL+) - Body ground
    Light control switch in the tail or head position
    11 to 14 V

    Text in Illustration 
    *a
    Component without harness connected
    (Navigation Receiver Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
  1. Disconnect the G5 navigation receiver assembly connector.

  1. Disconnect the F14 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G5-5 (ILL-) - F14-11 (ILL-)
    Always
    Below 1 Ω
    G5-5 (ILL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)