DTC P1613 Secondary Air Injection Driver Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| P1613 | Either condition (1) or (2) is met: (1) All conditions are met for 3 seconds or more (1 trip detection logic):
|
|
|
| |
|
|
| Related DTCs | P1613: Secondary air injection system air injection control driver circuit range check |
| Required Sensors/Components (Main) | Air injection control driver |
| Required Sensors/Components (Related) | Emission control valve set |
| Frequency of Operation | Once per driving cycle |
| Duration | 3 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | None |
| Battery voltage | 8 V or higher |
| Ignition switch | ON |
| Starter | OFF |
| Monitor runs whenever following DTCs not stored | None |
| Either a or b met: | - |
| a. Air pump | Not operating |
| b. Emission control valve | Not operating |
| Battery voltage | 8 V or higher |
| Ignition switch | ON |
| Starter | OFF |
| Monitor runs whenever following DTCs not stored | None |
| Following conditions (a) and (b) met | - |
| a. Air pump | Operating |
| b. Emission control valve | Operating |
| Battery voltage | 8 V or higher |
| Ignition switch | ON |
| Starter | OFF |
| One of following conditions met: | A, B, C or D |
| A. Diagnostic signal duty ratio from air injection control driver | 1 to 10% |
| B. Diagnostic signal duty ratio from air injection control driver | 30% |
| C. Diagnostic signal duty ratio from air injection control driver | 49% |
| D. Diagnostic signal duty ratio from air injection control driver | 91 to 99% |
| Diagnostic signal duty ratio from air injection control driver | 70 to 90% |
| Diagnostic signal duty ratio from air injection control driver | 0% |
| Diagnostic signal duty ratio from air injection control driver | 100% |
| Diagnostic signal duty ratio from air injection control driver | 70 to 90% when secondary air injection system operating. 0% when secondary air injection system not operating. |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK AIR INJECTION CONTROL DRIVER (POWER SOURCE CIRCUIT) |
![]() |
Disconnect the air injection control driver connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A44-1 (BATT) - Body ground | Always | 11 to 14 V (near battery voltage) |
| *a | Front view of wire harness connector (to Air Injection Control Driver) |
Reconnect the air injection control driver connector.
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - ECM, BODY GROUND) |
Disconnect the ECM connector.
Disconnect the air injection control driver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B37-23 (AIRP) - A45-4 (SIP) | Always | Below 1 Ω |
| B36-26 (AIRV) - A45-3 (SIV) | Always | Below 1 Ω |
| B37-30 (AIDI) - A45-2 (DI) | Always | Below 1 Ω |
| A45-1 (E) - Body ground | Always | Below 1 Ω |
| B37-23 (AIRP) or A45-4 (SIP) - Body ground | Always | 10 kΩ or higher |
| B36-26 (AIRV) or A45-3 (SIV) - Body ground | Always | 10 kΩ or higher |
| B37-30 (AIDI) or A45-2 (DI) - Body ground | Always | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the air injection control driver connector.
|
| ||||
| OK | |
| 3.INSPECT AIR INJECTION CONTROL DRIVER (DI TERMINAL VOLTAGE) |
![]() |
Disconnect the air injection control driver connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A45-2 (DI) - A45-1 (E) | Ignition switch ON | 11 to 14 V (near battery voltage) |
| *a | Front view of wire harness connector (to Air Injection Control Driver) |
Reconnect the air injection control driver connector.
|
| ||||
| OK | |
| 4.PERFORM ACTIVE TEST USING TECHSTREAM |
![]() |
Disconnect the air injection control driver connector.
Connect terminals DI and SIV of the wire harness connector for the air injection control driver.
| *1 | Air Injection Control Driver |
| *2 | ECM |
| *a | Front view of wire harness connector (to Air Injection Control Driver) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN.
Start the engine.
Perform the secondary air injection system forced operation while the engine is idling.
Measure the voltage between the SIV and E terminals of the ECM connector when the secondary air injection system is ON and OFF.
Turn the ignition switch off.
| Tester Connection | Condition | Specified Condition |
| A45-3 (SIV) - A45-1 (E) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| A45-3 (SIV) - A45-1 (E) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
![]() |
Connect terminals DI and SIP of the wire harness connector for the air injection control driver.
| *1 | Air Injection Control Driver |
| *2 | ECM |
| *a | Front view of wire harness connector (to Air Injection Control Driver) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN.
Start the engine.
Perform the secondary air injection system forced operation while the engine is idling.
Measure the voltage between the SIP and E terminals of the ECM connector when the secondary air injection system is ON and OFF.
Turn the ignition switch off.
| Tester Connection | Condition | Specified Condition |
| A45-4 (SIP) - A45-1 (E) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| A45-4 (SIP) - A45-1 (E) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
Reconnect the air injection control driver connector.
|
| ||||
| OK | |
| 5.REPLACE AIR INJECTION CONTROL DRIVER |
Replace the air injection control driver (Click here).
| NEXT | |
| 6.CHECK WHETHER DTC OUTPUT RECURS |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
Start the engine after the Techstream initialization is finished.
Perform the System Check operation by pressing ENTER (Next).
After operating the secondary air injection system, perform the following to confirm the secondary air injection system pending codes: Press the Exit button.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read the DTCs.
| Result | Proceed to |
| No DTC is output | A |
| Other DTCs are output | B |
Turn the ignition switch off.
|
| ||||
| A | ||
| ||