Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR

COMPRESSOR > INSTALLATION

for Preparation Click here



1. ADJUST COMPRESSOR OIL
  1. When replacing the compressor and magnetic clutch with a new one, gradually discharge the refrigerant gas from the service valve and drain the following amount of oil from the new compressor and magnetic clutch before installation.

    Standard:
    (Oil capacity inside the new compressor and magnetic clutch: 120 + 15 cc (4.1 + 0.51 fl.oz.)) - (Remaining oil amount in the removed compressor and magnetic clutch) = (Oil amount to be removed from the new compressor when replacing)

    NOTICE:
    1. When checking the compressor oil level, follow the A/C system precautions.
    2. If a new compressor and magnetic clutch is installed without removing some of the oil remaining in the pipes of the vehicle, the oil amount will be too large. This prevents heat exchange in the refrigerant cycle and causes refrigerant failure.
    3. If the volume of oil remaining in the removed compressor and magnetic clutch is too small, check for oil leakage.
    4. Be sure to use ND-OIL 8 or equivalent compressor oil.



2. INSTALL COOLER COMPRESSOR ASSEMBLY


E195719E01
  1. Install the cooler compressor with the stud bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the 3 bolts and nut.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    HINT:
    Tighten the bolts and nut in the order shown in the illustration.

  1. Connect the connector.



3. CONNECT SUCTION HOSE SUB-ASSEMBLY
  1. Remove the attached vinyl tape from the suction hose.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring to the suction hose.



    E199373E01
  1. Connect the suction hose with the 2 bolts.

    Torque:
    for bolt A:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }
    for bolt B:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



4. CONNECT DISCHARGE HOSE SUB-ASSEMBLY
  1. Remove the attached vinyl tape from the cooler refrigerant discharge hose.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring to the discharge hose.

  1. Connect the discharge hose to the cooler compressor with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



5. INSTALL GENERATOR ASSEMBLY
  1. Install the generator assembly (Click here).



6. CHARGE REFRIGERANT
SST
09985-20010   (09985-02130, 09985-02150, 09985-02090, 09985-02110, 09985-02010, 09985-02050, 09985-02060, 09985-02070)
  1. Perform vacuum purging using a vacuum pump.



  1. Charge refrigerant HFC-134a (R134a).

    Standard:
    550 +/-30 g (19.3 +/-1.0 oz.)



    I037365E19

    NOTICE:
    1. Do not operate the cooler compressor before charging refrigerant as the cooler compressor does not work properly without any refrigerant and overheats.
    2. Approximately 100 g (3.53 oz.) of refrigerant may need to be charged after bubbles disappear.



7. WARM UP ENGINE
  1. Warm up the engine at less than 1850 rpm for 2 minutes or more after charging the refrigerant.

    NOTICE:
    Be sure to warm up the compressor by turning the A/C switch on after removing and installing the cooler refrigerant lines (including the compressor) to prevent damage to the compressor.



8. CHECK FOR REFRIGERANT GAS LEAK
  1. After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.

  1. Perform the operation under these conditions:

    1. Stop the engine.
    2. Secure good ventilation (the halogen leak detector may react to volatile gases other than refrigerant, such as evaporated gasoline or exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that some refrigerant remains in the refrigeration system. When the compressor is off: approximately 392 to 588 kPa (4.0 to 6.0 kgf/cm2, 57 to 85 psi).



    I042222E34
  1. Using a halogen leak detector, check the refrigerant line for leakage.
    Text in Illustration 
    *1
    Halogen Leak Detector
    *a
    Check for Leakage

  1. If a gas leak from the drain hose is not detected, remove the blower motor control (blower resistor) from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.

  1. Disconnect the connector and wait for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.