Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1241    Low Power Supply Voltage Malfunction

for Preparation Click here


DESCRIPTION

If the voltage supplied to the IG1 terminal is within the DTC detection range due to malfunctions in components such as the battery and generator circuit, this DTC is stored.

DTC Code
DTC Detection Condition
Trouble Area
C1241
Either condition is met:
1. Both of the following conditions continue for at least 10 seconds.
  1. The vehicle speed is more than 3 km/h (2 mph).
  2. The IG1 terminal voltage is below 9.5 V.
2. All of the following conditions continue for at least 0.2 seconds.
  1. The solenoid relay remains on.
  2. The IG1 terminal voltage is below 9.5 V.
  3. The relay contact is open.
  1. Battery
  2. ECU-IG NO. 1 fuse
  3. Charging system
  4. Harness or connector
  5. Master cylinder solenoid (Skid control ECU)

WIRING DIAGRAM


C173289E08


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the master cylinder solenoid, perform calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.READ VALUE USING TECHSTREAM (IG1 VOLTAGE VALUE)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    IG1 Voltage Value
    IG1 voltage value/ Min.: 0.00 V, Max.: 20.00 V
    Ignition switch ON: 11 to 14 V
    -

  1. Check the voltage output from the skid control ECU displayed on the Techstream.

    OK:
    The output voltage displayed on the Techstream is within 11 to 14 V.



NG
Go to step 3
OK


2.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Check if the same DTCs are output (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output (When troubleshooting in accordance with Diagnostic Trouble Code Chart)
    B
    DTC is not output (When troubleshooting in accordance with Problem Symptoms Table)
    C



B
USE SIMULATION METHOD TO CHECK (Click here)

C
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)  

3.CHECK TERMINAL VOLTAGE (IG1)
  1. Disconnect the A6 skid control ECU connector.



    C214161E22
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A6-46 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)
  1. Disconnect the A6 and A7 skid control ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A6-1 (GND1) - Body ground
    Always
    Below 1 Ω
    A6-32 (GND2) - Body ground
    Always
    Below 1 Ω
    A7-4 (GND3) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Check if the same DTCs are output (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output (When troubleshooting in accordance with the Diagnostic Trouble Code Chart)
    B
    DTC is not output (When troubleshooting in accordance with the Problem Symptoms Table)
    C



B
USE SIMULATION METHOD TO CHECK (Click here)

C
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)