Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1252    Brake Booster Pump Motor on Time Abnormally Long

for Preparation Click here


DESCRIPTION

The motor relay (semiconductor relay) is built into the master cylinder solenoid and drives the pump motor based on a signal from the skid control ECU.

DTC Code
DTC Detection Condition
Trouble Area
C1252
The motor operates for 3 minutes or more.
  1. Brake booster with accumulator pump assembly
  2. Pump motor wire harness condition
  3. Master cylinder solenoid (Skid control ECU)
  4. Hydraulic brake booster assembly

HINT:
The pump motor continues operation for the first 3 minutes, and then starts and stops repeatedly.


INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform calibration (Click here).

HINT:
When DTC C1253, C1254, C1256 or C1452 is output together with DTC C1252, inspect and repair the trouble area indicated by DTC C1253, C1254, C1256 or C1452 first.

1.CHECK PUMP MOTOR OPERATION
  1. Turn the ignition switch off.

  1. Depress the brake pedal more than 40 times.

  1. Turn the ignition switch to ON.

  1. Check how the pump motor operates.

    Result 
    Result
    Proceed to
    Pump motor does not operate
    A
    Pump motor operates continuously and does not stop
    B
    Pump motor operates intermittently
    C
    Pump motor operates, and then stops
    D



B
REPLACE HYDRAULIC BRAKE BOOSTER ASSEMBLY (Click here)

C
Go to step 4

D
Go to step 5
A


2.CHECK CONNECTION OF PUMP MOTOR WIRE HARNESS
  1. Remove the hydraulic brake booster assembly (Click here).

  1. Check the tightening torque of the 2 screws which secure the wire harness connecting the master cylinder solenoid and brake booster with accumulator pump assembly .

OK:
The harness is tightened to the specified torque.

Torque:
2.9 N*m{ 30 kgf*cm , 26 in.*lbf }



NG
RETIGHTEN SCREWS
OK


3.CHECK RESISTANCE OF PUMP MOTOR WIRE HARNESS
  1. Using a screwdriver, remove the 2 screws and pull out the wire harness from the master cylinder solenoid.



    C173363E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Red wire terminal - Black wire terminal
    Always
    Below 2 Ω

    Text in Illustration 
    *1
    Pump motor wire harness
    *a
    Red wire
    *b
    Black wire



NG
REPLACE BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY (Click here)
OK


4.READ VALUE USING TECHSTREAM (ACCUMULATOR SENSOR)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Accumulator Sensor
    Accumulator pressure sensor reading/ Min.: 0.00 V, Max.: 5.00 V
    3.58 to 5 V
    If the value is constant regardless of the pump operation, an accumulator pressure sensor malfunction is suspected.

  1. Check the accumulator output value.

    Result 
    Result
    Proceed to
    Output value is within "Normal Condition" range
    A
    Output value is out of "Normal Condition" range
    B
    Output value is constant regardless of pump operation
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE HYDRAULIC BRAKE BOOSTER ASSEMBLY (Click here)
A


5.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON.

  1. Wait for more than 5 minutes.

  1. Check if the same DTC is output (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
REPLACE BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY (Click here)
A

REPLACE HYDRAULIC BRAKE BOOSTER ASSEMBLY (Click here)