Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0550    Power Steering Pressure Sensor Circuit Malfunction

DTC    P0552    Power Steering Pressure Sensor Circuit Low Input

DTC    P0553    Power Steering Pressure Sensor Circuit High Input

for Preparation Click here


DESCRIPTION

The power steering oil pressure switch is turned on when a power steering wheel load is generated by turning the steering wheel. The ECM regulates the engine idling speed according to the voltage output of the sensor.

DTC No.
DTC Detection Condition
Trouble Area
P0550
Power steering oil pressure switch voltage is below 0.28 V, or higher than 4.9 V for 0.5 seconds while the engine is running (1 trip detection logic).
  1. Open or short in power steering oil pressure switch circuit
  2. Power steering oil pressure switch
  3. ECM
P0552
Power steering oil pressure switch voltage is below 0.28 V for 0.5 seconds while the engine is running (1 trip detection logic).
  1. Open or short in power steering oil pressure switch circuit
  2. Power steering oil pressure switch
  3. ECM
P0553
Power steering oil pressure switch voltage is higher than 4.9 V for 0.5 seconds while the engine is running (1 trip detection logic).
  1. Open or short in power steering oil pressure switch circuit
  2. Power steering oil pressure switch
  3. ECM

WIRING DIAGRAM


A227106E01


MONITOR DESCRIPTION

The ECM monitors the power steering oil pressure switch voltage and uses this value to regulate the engine idling speed. When the power steering oil pressure switch output voltage deviates from the normal operating range, the ECM determines that there is a malfunction in the power steering oil pressure switch and stores a DTC.

MONITOR STRATEGY


Related DTCs
P0550: Power steering oil pressure switch range check (Chattering)
P0552: Power steering oil pressure switch range check (Low Resistance)
P0553: Power steering oil pressure switch range check (High Resistance)
Required sensors/Components (Main)
Power steering oil pressure switch
Frequency of operation
Continuous
Duration
0.5 seconds
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
Time after starter signal ON to OFF
2 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


P0550 
Power steering oil pressure switch voltage
Below 0.28 V, or higher than 4.9 V

P0552 
Power steering oil pressure switch voltage
Below 0.28 V

P0553 
Power steering oil pressure switch voltage
Higher than 4.9 V

CONFIRMATION DRIVING PATTERN


A198821E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine.
  7. Idle the engine for 5 seconds [B].
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0550, P0552 or P0553.
  12. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.

  13. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

HINT:
  1. If other DTCs relating to different systems that have terminal ETHW as the ground terminal are output simultaneously, terminal ETHW may have an open circuit.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK HARNESS AND CONNECTOR (ECM - POWER STEERING OIL PRESSURE SWITCH)
  1. Disconnect the ECM connector.

  1. Disconnect the power steering oil pressure switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B31-2 (PSP) - B37-16 (PSP)
    Always
    Below 1 Ω
    B31-1 (VC) - B36-16 (VCV2)
    Always
    Below 1 Ω
    B31-3 (E2) - B37-8 (ETHW)
    Always
    Below 1 Ω
    B31-2 (PSP) or B37-16 (PSP) - Body ground
    Always
    10 kΩ or higher
    B31-1 (VC) or B36-16 (VCV2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.REPLACE POWER STEERING OIL PRESSURE SWITCH
  1. Replace the power steering oil pressure switch (Click here).


NEXT


3.CONFIRM WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    P0550, P0552 and/or P0553 is output
    A
    No DTC is output
    B



B
END
A

REPLACE ECM (Click here)